Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 operating instructions Order no, Designation, SSPET5, Parts list

Models: SSPET 5

1 50

Page 49

SSPET5

SSPET5
Pos.	Order no.	Designation
1	85628	Brush holder with carbon
		(brush switching off)
2	83380	Turbine (1200 W)
3	97556	Solenoid valve
	85460	Ventilation valve
	85462	Compressed-air container
4	83080	Controller SSP
5	83379	Filter cartridges (4 pcs.)
6	83098	Controller SSE
7	28420	Sealing ring
8	85533	Tension ring
9	28839	Flap switch with plug
10	23093	Outlet flap with magnet
	85477	Nut
	85471	Screw
	93358	Disc
11	23098	Sealing ring
12	28626	Filter cloth
13	23091	Wire cloth
14	28625	Sealing

SM4-630

Parts list 48

Page 49

Image 49

Sterling SSPET 5 operating instructions Order no, Designation, SSPET5, Parts list

Contents

Operating Instructions Single Conveyor Unit For Powder SSPET Sterling Material ProcessingSM4-630 Sales and Contracting Department Parts and Service DepartmentSSPET5 Sterling Material Processing Technical serviceTelephone 800 Edition 02/01 Sterling order confirmation no SM4-630SSPET5 1. Safety instructions Table of contents2. Assembly instructions 3. Functional description6. Technical data 7. Parts list 8. Accessories SSPET5 5. MaintenanceSafety instructions 1. Safety instructionsSSPET5 Safety instructions SSPET5 1.1. Warnings and symbolsSSPET5 1.2. Explanations and information ∙ ∙ ∙ ∙ ∙ ∙Safety instructions Safety instructions SSPET5 1.3. For your safetyThis avoids injury and damage to equipment SSPET5 Safety instructionsSafety instructions ∙ ∙ ∙ ∙SSPET5 SSPET5 1.4. For the operating safety of the equipment Assembly instructions 2. Assembly instructionsSSPET5 The equipment is delivered as a complete assembly SSPET5 2.1. AssemblyAssembly instructions Assembly SM4-630 Assembly instructionsSSPET5 Assembly instructions SSPET5 2.2. Mounting the suction pipe MVConnect the inner pipe with the straight end to a flexible hose Assembly instructions SSPET5 2.3. Electrical connectionThe operating voltage is 230 V/50 Hz Special voltages on request 2.3.2. Installation of the signal line of the SKW optional SSPET5 2.3.1. Installation of the “flap switch” signal lineInsert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller Assembly instructionsSSPET5 Assembly instructionsThis work must be carried out by qualified personnel only For operating the cleaning unit, a compressed-air supply is necessary SSPET5 2.4. Compressed-air supplyAssembly instructions Functional description 3. Functional descriptionSSPET5 The filter-cleaning process takes place during the conveying process SSPET5 3.1. GeneralFunctional description The emptying time consists of 8 seconds SSPET5 3.2. Controller SSEFunctional description SSPET5 An “E” appears in the display and an error numberFunctional description Functional description SSPET5 3.3. Controller SSPPutting into operation 4. Putting into operationSSPET5 Remove the flexible hose from the connected material takeup SSPET5 4.1. Checking the pipe systemPutting into operation If the conditions points 3 + 4 are not met SSPET5 4.2. Adjusting the suction pipesIf the conditions points 3 + 4 are met Putting into operationSetting the conveying time SSPET5 4.3. Setting the controller SSEThe turbine is running but no material is being conveyed The conveying capacity is too lowthe “change-over” key SSPET5 Setting the line clear timeIf no line clear valve has been installed enter “0 Press the “arrow key” andSetting the pulse duration Press the “arrow key” SSPET5 4.4. Setting the controller SSPSetting the time interval the “change-over” keySSPET5 4.5. Initial conveying operations 4.6. Alarm Messages displayed on the controller SSEPutting into operation SSPET5 The following error messages can be displayedPutting into operation 4.8. Switching off the unit SSPET5 4.7. Alarm Messages displayed on the controller SSPPutting into operation Maintenance 5. MaintenanceSSPET5 Maintenance Please observe the maintenance intervalsSSPET5 Maintenance SSPET5 5.1. Maintenance intervalsDaily SSPET5 5.2. Servicing the conveyor 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unitMaintenance Removal InstallationMaintenance SSPET5Maintenance SSPET5 5.2.2. Changing the sealing ring of the outlet flapAssembly sealing ring SM4-630Maintenance SSPET5 5.2.3. Adjusting the flap switchMaintenance SSPET5 5.3. Replacing carbon brushes at turbineSSPET5 SM4-630 Maintenance SSPET5 InstallationOptional Features 6. Technical dataTechnical data Basic VersionTechnical data SSPET5 Dimension SheetSM4-630 Parts list 7. Parts listThis parts list is only for the use of trained personnel only SSPET5Parts list SSPET5 SSPET5SM4-630 Designation Order noParts list SSPET5Accessories 8. AccessoriesSSPET5 SM4-630

Order no.

Designation