Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 operating instructions SSPET5, Assembly instructions, Assembly SM4-630

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 16

Image 16

SSPET5

Mounting on fixed machine throats or intermediate containers is done by means of strap retainers.

Please check during assembly that the admissible bearing loads are not ex- ceeded.

Mount the conveyor in such a way that the outlet flap swings in a right angle to the direction of machine movement.

Please check that all connecting points are tight to ensure that the conveying per- formance is not impaired.

J L

Assembly

SM4-630

Assembly instructions 15

Page 16

Image 16

Sterling SSPET 5 operating instructions SSPET5, Assembly instructions, Assembly SM4-630

Contents

Operating Instructions Single Conveyor Unit For Powder SSPET Sterling Material ProcessingSM4-630 Parts and Service Department Sales and Contracting DepartmentTechnical service SSPET5 Sterling Material ProcessingTelephone 800 Edition 02/01 Sterling order confirmation no SM4-630SSPET5 Table of contents 1. Safety instructions2. Assembly instructions 3. Functional descriptionSSPET5 5. Maintenance 6. Technical data 7. Parts list 8. AccessoriesSafety instructions 1. Safety instructionsSSPET5 SSPET5 1.1. Warnings and symbols Safety instructionsSSPET5 1.2. Explanations and information ∙ ∙ ∙ ∙ ∙ ∙Safety instructions Safety instructions SSPET5 1.3. For your safetyThis avoids injury and damage to equipment Safety instructions SSPET5Safety instructions ∙ ∙ ∙ ∙SSPET5 SSPET5 1.4. For the operating safety of the equipment Assembly instructions 2. Assembly instructionsSSPET5 The equipment is delivered as a complete assembly SSPET5 2.1. AssemblyAssembly instructions Assembly SM4-630 Assembly instructionsSSPET5 Assembly instructions SSPET5 2.2. Mounting the suction pipe MVConnect the inner pipe with the straight end to a flexible hose Assembly instructions SSPET5 2.3. Electrical connectionThe operating voltage is 230 V/50 Hz Special voltages on request SSPET5 2.3.1. Installation of the “flap switch” signal line 2.3.2. Installation of the signal line of the SKW optionalInsert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller Assembly instructionsSSPET5 Assembly instructionsThis work must be carried out by qualified personnel only For operating the cleaning unit, a compressed-air supply is necessary SSPET5 2.4. Compressed-air supplyAssembly instructions Functional description 3. Functional descriptionSSPET5 The filter-cleaning process takes place during the conveying process SSPET5 3.1. GeneralFunctional description The emptying time consists of 8 seconds SSPET5 3.2. Controller SSEFunctional description SSPET5 An “E” appears in the display and an error numberFunctional description SSPET5 3.3. Controller SSP Functional descriptionPutting into operation 4. Putting into operationSSPET5 Remove the flexible hose from the connected material takeup SSPET5 4.1. Checking the pipe systemPutting into operation SSPET5 4.2. Adjusting the suction pipes If the conditions points 3 + 4 are not metIf the conditions points 3 + 4 are met Putting into operationSSPET5 4.3. Setting the controller SSE Setting the conveying timeThe turbine is running but no material is being conveyed The conveying capacity is too lowSSPET5 Setting the line clear time the “change-over” keyIf no line clear valve has been installed enter “0 Press the “arrow key” andSSPET5 4.4. Setting the controller SSP Setting the pulse duration Press the “arrow key”Setting the time interval the “change-over” keySSPET5 4.5. Initial conveying operations 4.6. Alarm Messages displayed on the controller SSEPutting into operation SSPET5 The following error messages can be displayedPutting into operation 4.8. Switching off the unit SSPET5 4.7. Alarm Messages displayed on the controller SSPPutting into operation Maintenance 5. MaintenanceSSPET5 Maintenance Please observe the maintenance intervalsSSPET5 Maintenance SSPET5 5.1. Maintenance intervalsDaily SSPET5 5.2. Servicing the conveyor 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unitMaintenance Installation RemovalMaintenance SSPET5SSPET5 5.2.2. Changing the sealing ring of the outlet flap MaintenanceAssembly sealing ring SM4-630SSPET5 5.2.3. Adjusting the flap switch MaintenanceMaintenance SSPET5 5.3. Replacing carbon brushes at turbineSSPET5 SM4-630 SSPET5 Installation Maintenance6. Technical data Optional FeaturesTechnical data Basic VersionTechnical data SSPET5 Dimension SheetSM4-630 7. Parts list Parts listThis parts list is only for the use of trained personnel only SSPET5Parts list SSPET5 SSPET5SM4-630 Order no DesignationParts list SSPET58. Accessories AccessoriesSSPET5 SM4-630