Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 SSPET5 5.2.2. Changing the sealing ring of the outlet flap, Maintenance, SM4-630

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 41

Image 41

SSPET5

5.2.2. Changing the sealing ring of the outlet flap

Draw the old sealing ring off the nozzle of the material outlet.

Install the new sealing ring.

Assembly sealing ring

Observe the direction of installation.

Install the unit.

Order number

sealing ring:

ID 23098

SM4-630

Maintenance 40

Page 41

Image 41

Sterling SSPET 5 SSPET5 5.2.2. Changing the sealing ring of the outlet flap, Maintenance, Assembly sealing ring, SM4-630

Contents

SM4-630 Sterling Material ProcessingOperating Instructions Single Conveyor Unit For Powder SSPET Sales and Contracting Department Parts and Service DepartmentSSPET5 Sterling Material Processing Technical serviceTelephone 800 Edition 02/01 Sterling order confirmation no SM4-630SSPET5 1. Safety instructions Table of contents2. Assembly instructions 3. Functional description6. Technical data 7. Parts list 8. Accessories SSPET5 5. MaintenanceSSPET5 1. Safety instructionsSafety instructions Safety instructions SSPET5 1.1. Warnings and symbolsSafety instructions ∙ ∙ ∙ ∙ ∙ ∙SSPET5 1.2. Explanations and information This avoids injury and damage to equipment SSPET5 1.3. For your safetySafety instructions SSPET5 Safety instructionsSSPET5 ∙ ∙ ∙ ∙Safety instructions SSPET5 1.4. For the operating safety of the equipment SSPET5 2. Assembly instructionsAssembly instructions Assembly instructions SSPET5 2.1. AssemblyThe equipment is delivered as a complete assembly SSPET5 Assembly instructionsAssembly SM4-630 Connect the inner pipe with the straight end to a flexible hose SSPET5 2.2. Mounting the suction pipe MVAssembly instructions The operating voltage is 230 V/50 Hz Special voltages on request SSPET5 2.3. Electrical connectionAssembly instructions 2.3.2. Installation of the signal line of the SKW optional SSPET5 2.3.1. Installation of the “flap switch” signal lineInsert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller Assembly instructionsThis work must be carried out by qualified personnel only Assembly instructionsSSPET5 Assembly instructions SSPET5 2.4. Compressed-air supplyFor operating the cleaning unit, a compressed-air supply is necessary SSPET5 3. Functional descriptionFunctional description Functional description SSPET5 3.1. GeneralThe filter-cleaning process takes place during the conveying process Functional description SSPET5 3.2. Controller SSEThe emptying time consists of 8 seconds Functional description An “E” appears in the display and an error numberSSPET5 Functional description SSPET5 3.3. Controller SSPSSPET5 4. Putting into operationPutting into operation Putting into operation SSPET5 4.1. Checking the pipe systemRemove the flexible hose from the connected material takeup If the conditions points 3 + 4 are not met SSPET5 4.2. Adjusting the suction pipesIf the conditions points 3 + 4 are met Putting into operationSetting the conveying time SSPET5 4.3. Setting the controller SSEThe turbine is running but no material is being conveyed The conveying capacity is too lowthe “change-over” key SSPET5 Setting the line clear timeIf no line clear valve has been installed enter “0 Press the “arrow key” andSetting the pulse duration Press the “arrow key” SSPET5 4.4. Setting the controller SSPSetting the time interval the “change-over” keyPutting into operation 4.6. Alarm Messages displayed on the controller SSESSPET5 4.5. Initial conveying operations Putting into operation The following error messages can be displayedSSPET5 Putting into operation SSPET5 4.7. Alarm Messages displayed on the controller SSP4.8. Switching off the unit SSPET5 5. MaintenanceMaintenance SSPET5 Please observe the maintenance intervalsMaintenance Daily SSPET5 5.1. Maintenance intervalsMaintenance Maintenance 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unitSSPET5 5.2. Servicing the conveyor Removal InstallationMaintenance SSPET5Maintenance SSPET5 5.2.2. Changing the sealing ring of the outlet flapAssembly sealing ring SM4-630Maintenance SSPET5 5.2.3. Adjusting the flap switchSSPET5 SM4-630 SSPET5 5.3. Replacing carbon brushes at turbineMaintenance Maintenance SSPET5 InstallationOptional Features 6. Technical dataTechnical data Basic VersionSM4-630 SSPET5 Dimension SheetTechnical data Parts list 7. Parts listThis parts list is only for the use of trained personnel only SSPET5SM4-630 SSPET5 SSPET5Parts list Designation Order noParts list SSPET5Accessories 8. AccessoriesSSPET5 SM4-630