Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 operating instructions SSPET5 5.2. Servicing the conveyor, Maintenance

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 39

Image 39

SSPET5

5.2. Servicing the conveyor

Disconnect the unit from mains supply by the device plug.

Depressurize all system sections of the equipment (only units with active cleaning).

Disassembly the unit.

5.2.1. Cleaning/replacing the filter cartridges of the cleaning unit

Clean the separator hopper each time you are changing the materials.

Use only cleaning agents which fulfil the corresponding re- quirements.

Only clean the separator hopper with compressed-air and/or a brush.

The conveying capacity is diminished by a clogged filter car- tridge.

SM4-630

Maintenance 38

Page 39

Image 39

Sterling SSPET 5 SSPET5 5.2. Servicing the conveyor, Cleaning/replacing the filter cartridges of the cleaning unit

Contents

Sterling Material Processing Operating Instructions Single Conveyor Unit For Powder SSPETSM4-630 Sales and Contracting Department Parts and Service DepartmentSM4-630 Technical serviceSSPET5 Sterling Material Processing Telephone 800 Edition 02/01 Sterling order confirmation noSSPET5 3. Functional description Table of contents1. Safety instructions 2. Assembly instructions6. Technical data 7. Parts list 8. Accessories SSPET5 5. Maintenance1. Safety instructions Safety instructionsSSPET5 Safety instructions SSPET5 1.1. Warnings and symbols∙ ∙ ∙ ∙ ∙ ∙ SSPET5 1.2. Explanations and informationSafety instructions SSPET5 1.3. For your safety Safety instructionsThis avoids injury and damage to equipment SSPET5 Safety instructions∙ ∙ ∙ ∙ Safety instructionsSSPET5 SSPET5 1.4. For the operating safety of the equipment 2. Assembly instructions Assembly instructionsSSPET5 SSPET5 2.1. Assembly The equipment is delivered as a complete assemblyAssembly instructions Assembly instructions Assembly SM4-630SSPET5 SSPET5 2.2. Mounting the suction pipe MV Assembly instructionsConnect the inner pipe with the straight end to a flexible hose SSPET5 2.3. Electrical connection Assembly instructionsThe operating voltage is 230 V/50 Hz Special voltages on request Assembly instructions SSPET5 2.3.1. Installation of the “flap switch” signal line2.3.2. Installation of the signal line of the SKW optional Insert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controllerAssembly instructions SSPET5This work must be carried out by qualified personnel only SSPET5 2.4. Compressed-air supply For operating the cleaning unit, a compressed-air supply is necessaryAssembly instructions 3. Functional description Functional descriptionSSPET5 SSPET5 3.1. General The filter-cleaning process takes place during the conveying processFunctional description SSPET5 3.2. Controller SSE The emptying time consists of 8 secondsFunctional description An “E” appears in the display and an error number SSPET5Functional description Functional description SSPET5 3.3. Controller SSP4. Putting into operation Putting into operationSSPET5 SSPET5 4.1. Checking the pipe system Remove the flexible hose from the connected material takeupPutting into operation Putting into operation SSPET5 4.2. Adjusting the suction pipesIf the conditions points 3 + 4 are not met If the conditions points 3 + 4 are metThe conveying capacity is too low SSPET5 4.3. Setting the controller SSESetting the conveying time The turbine is running but no material is being conveyedPress the “arrow key” and SSPET5 Setting the line clear timethe “change-over” key If no line clear valve has been installed enter “0the “change-over” key SSPET5 4.4. Setting the controller SSPSetting the pulse duration Press the “arrow key” Setting the time interval4.6. Alarm Messages displayed on the controller SSE SSPET5 4.5. Initial conveying operationsPutting into operation The following error messages can be displayed SSPET5Putting into operation SSPET5 4.7. Alarm Messages displayed on the controller SSP 4.8. Switching off the unitPutting into operation 5. Maintenance MaintenanceSSPET5 Please observe the maintenance intervals MaintenanceSSPET5 SSPET5 5.1. Maintenance intervals MaintenanceDaily 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unit SSPET5 5.2. Servicing the conveyorMaintenance SSPET5 InstallationRemoval MaintenanceSM4-630 SSPET5 5.2.2. Changing the sealing ring of the outlet flapMaintenance Assembly sealing ringMaintenance SSPET5 5.2.3. Adjusting the flap switchSSPET5 5.3. Replacing carbon brushes at turbine MaintenanceSSPET5 SM4-630 Maintenance SSPET5 InstallationBasic Version 6. Technical dataOptional Features Technical dataSSPET5 Dimension Sheet Technical dataSM4-630 SSPET5 7. Parts listParts list This parts list is only for the use of trained personnel onlySSPET5 SSPET5 Parts listSM4-630 SSPET5 Order noDesignation Parts listSM4-630 8. AccessoriesAccessories SSPET5