Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 operating instructions SSPET5 Dimension Sheet, Technical data, SM4-630

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 46

SSPET5

SSPET5

Dimension Sheet

Dimensions and data without obligation. Dimensions in mm. (in.) Specifications may be subject to alterations.

SM4-630

Technical data 45

Image 46

Sterling SSPET 5 operating instructions SSPET5 Dimension Sheet, Technical data, SM4-630

Contents

Operating Instructions Single Conveyor Unit For Powder SSPET Sterling Material ProcessingSM4-630 Parts and Service Department Sales and Contracting DepartmentTelephone 800 Edition 02/01 Sterling order confirmation no Technical serviceSSPET5 Sterling Material Processing SM4-630SSPET5 2. Assembly instructions Table of contents1. Safety instructions 3. Functional descriptionSSPET5 5. Maintenance 6. Technical data 7. Parts list 8. AccessoriesSafety instructions 1. Safety instructionsSSPET5 SSPET5 1.1. Warnings and symbols Safety instructionsSSPET5 1.2. Explanations and information ∙ ∙ ∙ ∙ ∙ ∙Safety instructions Safety instructions SSPET5 1.3. For your safetyThis avoids injury and damage to equipment Safety instructions SSPET5Safety instructions ∙ ∙ ∙ ∙SSPET5 SSPET5 1.4. For the operating safety of the equipment Assembly instructions 2. Assembly instructionsSSPET5 The equipment is delivered as a complete assembly SSPET5 2.1. AssemblyAssembly instructions Assembly SM4-630 Assembly instructionsSSPET5 Assembly instructions SSPET5 2.2. Mounting the suction pipe MVConnect the inner pipe with the straight end to a flexible hose Assembly instructions SSPET5 2.3. Electrical connectionThe operating voltage is 230 V/50 Hz Special voltages on request Insert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller SSPET5 2.3.1. Installation of the “flap switch” signal line2.3.2. Installation of the signal line of the SKW optional Assembly instructionsSSPET5 Assembly instructionsThis work must be carried out by qualified personnel only For operating the cleaning unit, a compressed-air supply is necessary SSPET5 2.4. Compressed-air supplyAssembly instructions Functional description 3. Functional descriptionSSPET5 The filter-cleaning process takes place during the conveying process SSPET5 3.1. GeneralFunctional description The emptying time consists of 8 seconds SSPET5 3.2. Controller SSEFunctional description SSPET5 An “E” appears in the display and an error numberFunctional description SSPET5 3.3. Controller SSP Functional descriptionPutting into operation 4. Putting into operationSSPET5 Remove the flexible hose from the connected material takeup SSPET5 4.1. Checking the pipe systemPutting into operation If the conditions points 3 + 4 are met SSPET5 4.2. Adjusting the suction pipesIf the conditions points 3 + 4 are not met Putting into operationThe turbine is running but no material is being conveyed SSPET5 4.3. Setting the controller SSESetting the conveying time The conveying capacity is too lowIf no line clear valve has been installed enter “0 SSPET5 Setting the line clear timethe “change-over” key Press the “arrow key” andSetting the time interval SSPET5 4.4. Setting the controller SSPSetting the pulse duration Press the “arrow key” the “change-over” keySSPET5 4.5. Initial conveying operations 4.6. Alarm Messages displayed on the controller SSEPutting into operation SSPET5 The following error messages can be displayedPutting into operation 4.8. Switching off the unit SSPET5 4.7. Alarm Messages displayed on the controller SSPPutting into operation Maintenance 5. MaintenanceSSPET5 Maintenance Please observe the maintenance intervalsSSPET5 Maintenance SSPET5 5.1. Maintenance intervalsDaily SSPET5 5.2. Servicing the conveyor 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unitMaintenance Maintenance InstallationRemoval SSPET5Assembly sealing ring SSPET5 5.2.2. Changing the sealing ring of the outlet flapMaintenance SM4-630SSPET5 5.2.3. Adjusting the flap switch MaintenanceMaintenance SSPET5 5.3. Replacing carbon brushes at turbineSSPET5 SM4-630 SSPET5 Installation MaintenanceTechnical data 6. Technical dataOptional Features Basic VersionTechnical data SSPET5 Dimension SheetSM4-630 This parts list is only for the use of trained personnel only 7. Parts listParts list SSPET5Parts list SSPET5 SSPET5SM4-630 Parts list Order noDesignation SSPET5SSPET5 8. AccessoriesAccessories SM4-630