Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 operating instructions ∙ ∙ ∙ ∙, SSPET5, Safety instructions

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 12

Image 12

SSPET5

∙This equipment is not suitable for foods processing.

∙Observe that sound intensity levels over 85 dB(A), may cause prolonged damage to health. Use suitable earmuffs. This avoids impairment of hearing!

∙

Attachments not supplied by Sterling must be manufactured in accordance with safety regulation EN 294. Caution! Danger of accidents!

Check all lines, hoses and screwed connections regularly for leaks and obvious damage. Repair damage immediately. Caution: Danger of accidents!

Depressurize all system sections of the equipment before carrying out any repair work. Caution: Danger of accidents!

The equipment may only be operated when all the associated components are properly connected up and in accordance with the relevant regulations.

∙The safety instructions of the connected machines must be followed.

SM4-630

Safety instructions 11

Page 12

Image 12

Sterling SSPET 5 operating instructions ∙ ∙ ∙ ∙, SSPET5, Safety instructions

Contents

Sterling Material Processing Operating Instructions Single Conveyor Unit For Powder SSPETSM4-630 Parts and Service Department Sales and Contracting DepartmentTechnical service SSPET5 Sterling Material ProcessingTelephone 800 Edition 02/01 Sterling order confirmation no SM4-630SSPET5 Table of contents 1. Safety instructions2. Assembly instructions 3. Functional descriptionSSPET5 5. Maintenance 6. Technical data 7. Parts list 8. Accessories1. Safety instructions Safety instructionsSSPET5 SSPET5 1.1. Warnings and symbols Safety instructions∙ ∙ ∙ ∙ ∙ ∙ SSPET5 1.2. Explanations and informationSafety instructions SSPET5 1.3. For your safety Safety instructionsThis avoids injury and damage to equipment Safety instructions SSPET5∙ ∙ ∙ ∙ Safety instructionsSSPET5 SSPET5 1.4. For the operating safety of the equipment 2. Assembly instructions Assembly instructionsSSPET5 SSPET5 2.1. Assembly The equipment is delivered as a complete assemblyAssembly instructions Assembly instructions Assembly SM4-630SSPET5 SSPET5 2.2. Mounting the suction pipe MV Assembly instructionsConnect the inner pipe with the straight end to a flexible hose SSPET5 2.3. Electrical connection Assembly instructionsThe operating voltage is 230 V/50 Hz Special voltages on request SSPET5 2.3.1. Installation of the “flap switch” signal line 2.3.2. Installation of the signal line of the SKW optionalInsert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller Assembly instructionsAssembly instructions SSPET5This work must be carried out by qualified personnel only SSPET5 2.4. Compressed-air supply For operating the cleaning unit, a compressed-air supply is necessaryAssembly instructions 3. Functional description Functional descriptionSSPET5 SSPET5 3.1. General The filter-cleaning process takes place during the conveying processFunctional description SSPET5 3.2. Controller SSE The emptying time consists of 8 secondsFunctional description An “E” appears in the display and an error number SSPET5Functional description SSPET5 3.3. Controller SSP Functional description4. Putting into operation Putting into operationSSPET5 SSPET5 4.1. Checking the pipe system Remove the flexible hose from the connected material takeupPutting into operation SSPET5 4.2. Adjusting the suction pipes If the conditions points 3 + 4 are not metIf the conditions points 3 + 4 are met Putting into operationSSPET5 4.3. Setting the controller SSE Setting the conveying timeThe turbine is running but no material is being conveyed The conveying capacity is too lowSSPET5 Setting the line clear time the “change-over” keyIf no line clear valve has been installed enter “0 Press the “arrow key” andSSPET5 4.4. Setting the controller SSP Setting the pulse duration Press the “arrow key”Setting the time interval the “change-over” key4.6. Alarm Messages displayed on the controller SSE SSPET5 4.5. Initial conveying operationsPutting into operation The following error messages can be displayed SSPET5Putting into operation SSPET5 4.7. Alarm Messages displayed on the controller SSP 4.8. Switching off the unitPutting into operation 5. Maintenance MaintenanceSSPET5 Please observe the maintenance intervals MaintenanceSSPET5 SSPET5 5.1. Maintenance intervals MaintenanceDaily 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unit SSPET5 5.2. Servicing the conveyorMaintenance Installation RemovalMaintenance SSPET5SSPET5 5.2.2. Changing the sealing ring of the outlet flap MaintenanceAssembly sealing ring SM4-630SSPET5 5.2.3. Adjusting the flap switch MaintenanceSSPET5 5.3. Replacing carbon brushes at turbine MaintenanceSSPET5 SM4-630 SSPET5 Installation Maintenance6. Technical data Optional FeaturesTechnical data Basic VersionSSPET5 Dimension Sheet Technical dataSM4-630 7. Parts list Parts listThis parts list is only for the use of trained personnel only SSPET5SSPET5 SSPET5 Parts listSM4-630 Order no DesignationParts list SSPET58. Accessories AccessoriesSSPET5 SM4-630