Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 SSPET5 Setting the line clear time, the “change-over” key, SM4-630

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 31

Image 31

SSPET5

Setting the line clear time

Press the “arrow key” and

the “change-over” key.

The line clear time which was last selected appears in the display.

0-99 seconds may be set for the line clear time.

If no line clear valve has been installed enter “0".

SM4-630

Putting into operation 30

Page 31

Image 31

Sterling SSPET 5 SSPET5 Setting the line clear time, the “change-over” key, Press the “arrow key” and, SM4-630

Contents

Operating Instructions Single Conveyor Unit For Powder SSPET Sterling Material ProcessingSM4-630 Sales and Contracting Department Parts and Service DepartmentSM4-630 Technical serviceSSPET5 Sterling Material Processing Telephone 800 Edition 02/01 Sterling order confirmation noSSPET5 3. Functional description Table of contents1. Safety instructions 2. Assembly instructions6. Technical data 7. Parts list 8. Accessories SSPET5 5. MaintenanceSafety instructions 1. Safety instructionsSSPET5 Safety instructions SSPET5 1.1. Warnings and symbolsSSPET5 1.2. Explanations and information ∙ ∙ ∙ ∙ ∙ ∙Safety instructions Safety instructions SSPET5 1.3. For your safetyThis avoids injury and damage to equipment SSPET5 Safety instructionsSafety instructions ∙ ∙ ∙ ∙SSPET5 SSPET5 1.4. For the operating safety of the equipment Assembly instructions 2. Assembly instructionsSSPET5 The equipment is delivered as a complete assembly SSPET5 2.1. AssemblyAssembly instructions Assembly SM4-630 Assembly instructionsSSPET5 Assembly instructions SSPET5 2.2. Mounting the suction pipe MVConnect the inner pipe with the straight end to a flexible hose Assembly instructions SSPET5 2.3. Electrical connectionThe operating voltage is 230 V/50 Hz Special voltages on request Assembly instructions SSPET5 2.3.1. Installation of the “flap switch” signal line2.3.2. Installation of the signal line of the SKW optional Insert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controllerSSPET5 Assembly instructionsThis work must be carried out by qualified personnel only For operating the cleaning unit, a compressed-air supply is necessary SSPET5 2.4. Compressed-air supplyAssembly instructions Functional description 3. Functional descriptionSSPET5 The filter-cleaning process takes place during the conveying process SSPET5 3.1. GeneralFunctional description The emptying time consists of 8 seconds SSPET5 3.2. Controller SSEFunctional description SSPET5 An “E” appears in the display and an error numberFunctional description Functional description SSPET5 3.3. Controller SSPPutting into operation 4. Putting into operationSSPET5 Remove the flexible hose from the connected material takeup SSPET5 4.1. Checking the pipe systemPutting into operation Putting into operation SSPET5 4.2. Adjusting the suction pipesIf the conditions points 3 + 4 are not met If the conditions points 3 + 4 are metThe conveying capacity is too low SSPET5 4.3. Setting the controller SSESetting the conveying time The turbine is running but no material is being conveyedPress the “arrow key” and SSPET5 Setting the line clear timethe “change-over” key If no line clear valve has been installed enter “0the “change-over” key SSPET5 4.4. Setting the controller SSPSetting the pulse duration Press the “arrow key” Setting the time intervalSSPET5 4.5. Initial conveying operations 4.6. Alarm Messages displayed on the controller SSEPutting into operation SSPET5 The following error messages can be displayedPutting into operation 4.8. Switching off the unit SSPET5 4.7. Alarm Messages displayed on the controller SSPPutting into operation Maintenance 5. MaintenanceSSPET5 Maintenance Please observe the maintenance intervalsSSPET5 Maintenance SSPET5 5.1. Maintenance intervalsDaily SSPET5 5.2. Servicing the conveyor 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unitMaintenance SSPET5 InstallationRemoval MaintenanceSM4-630 SSPET5 5.2.2. Changing the sealing ring of the outlet flapMaintenance Assembly sealing ringMaintenance SSPET5 5.2.3. Adjusting the flap switchMaintenance SSPET5 5.3. Replacing carbon brushes at turbineSSPET5 SM4-630 Maintenance SSPET5 InstallationBasic Version 6. Technical dataOptional Features Technical dataTechnical data SSPET5 Dimension SheetSM4-630 SSPET5 7. Parts listParts list This parts list is only for the use of trained personnel onlyParts list SSPET5 SSPET5SM4-630 SSPET5 Order noDesignation Parts listSM4-630 8. AccessoriesAccessories SSPET5