Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 SSPET5, This work must be carried out by qualified personnel only

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 20

Image 20

This work must be carried out by qualified personnel only.

SSPET5

2.3.3.Installation of an alarm indicating device at the SSE controller (optional)

This work must be carried out by qualified personnel only.

Disconnect the unit from mains supply by the device plug before you begin with works on the controller. Danger to life!

The connection is potential-free and rated for no more than 5 A.

An additional alarm indicating device (e.g. horn, signal light) can be connected.

You need an “acknowledgement key” for 24 V (e.g. by Rafi Company).

SM4-630

Assembly instructions 19

Page 20

Image 20

Sterling SSPET 5 SSPET5, This work must be carried out by qualified personnel only, Assembly instructions

Contents

SM4-630 Sterling Material ProcessingOperating Instructions Single Conveyor Unit For Powder SSPET Parts and Service Department Sales and Contracting DepartmentTechnical service SSPET5 Sterling Material ProcessingTelephone 800 Edition 02/01 Sterling order confirmation no SM4-630SSPET5 Table of contents 1. Safety instructions2. Assembly instructions 3. Functional descriptionSSPET5 5. Maintenance 6. Technical data 7. Parts list 8. AccessoriesSSPET5 1. Safety instructionsSafety instructions SSPET5 1.1. Warnings and symbols Safety instructionsSafety instructions ∙ ∙ ∙ ∙ ∙ ∙SSPET5 1.2. Explanations and information This avoids injury and damage to equipment SSPET5 1.3. For your safetySafety instructions Safety instructions SSPET5SSPET5 ∙ ∙ ∙ ∙Safety instructions SSPET5 1.4. For the operating safety of the equipment SSPET5 2. Assembly instructionsAssembly instructions Assembly instructions SSPET5 2.1. AssemblyThe equipment is delivered as a complete assembly SSPET5 Assembly instructionsAssembly SM4-630 Connect the inner pipe with the straight end to a flexible hose SSPET5 2.2. Mounting the suction pipe MVAssembly instructions The operating voltage is 230 V/50 Hz Special voltages on request SSPET5 2.3. Electrical connectionAssembly instructions SSPET5 2.3.1. Installation of the “flap switch” signal line 2.3.2. Installation of the signal line of the SKW optionalInsert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller Assembly instructionsThis work must be carried out by qualified personnel only Assembly instructionsSSPET5 Assembly instructions SSPET5 2.4. Compressed-air supplyFor operating the cleaning unit, a compressed-air supply is necessary SSPET5 3. Functional descriptionFunctional description Functional description SSPET5 3.1. GeneralThe filter-cleaning process takes place during the conveying process Functional description SSPET5 3.2. Controller SSEThe emptying time consists of 8 seconds Functional description An “E” appears in the display and an error numberSSPET5 SSPET5 3.3. Controller SSP Functional descriptionSSPET5 4. Putting into operationPutting into operation Putting into operation SSPET5 4.1. Checking the pipe systemRemove the flexible hose from the connected material takeup SSPET5 4.2. Adjusting the suction pipes If the conditions points 3 + 4 are not metIf the conditions points 3 + 4 are met Putting into operationSSPET5 4.3. Setting the controller SSE Setting the conveying timeThe turbine is running but no material is being conveyed The conveying capacity is too lowSSPET5 Setting the line clear time the “change-over” keyIf no line clear valve has been installed enter “0 Press the “arrow key” andSSPET5 4.4. Setting the controller SSP Setting the pulse duration Press the “arrow key”Setting the time interval the “change-over” keyPutting into operation 4.6. Alarm Messages displayed on the controller SSESSPET5 4.5. Initial conveying operations Putting into operation The following error messages can be displayedSSPET5 Putting into operation SSPET5 4.7. Alarm Messages displayed on the controller SSP4.8. Switching off the unit SSPET5 5. MaintenanceMaintenance SSPET5 Please observe the maintenance intervalsMaintenance Daily SSPET5 5.1. Maintenance intervalsMaintenance Maintenance 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unitSSPET5 5.2. Servicing the conveyor Installation RemovalMaintenance SSPET5SSPET5 5.2.2. Changing the sealing ring of the outlet flap MaintenanceAssembly sealing ring SM4-630SSPET5 5.2.3. Adjusting the flap switch MaintenanceSSPET5 SM4-630 SSPET5 5.3. Replacing carbon brushes at turbineMaintenance SSPET5 Installation Maintenance6. Technical data Optional FeaturesTechnical data Basic VersionSM4-630 SSPET5 Dimension SheetTechnical data 7. Parts list Parts listThis parts list is only for the use of trained personnel only SSPET5SM4-630 SSPET5 SSPET5Parts list Order no DesignationParts list SSPET58. Accessories AccessoriesSSPET5 SM4-630