Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 operating instructions SSPET5 3.3. Controller SSP, Functional description

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 26

Image 26

SSPET5

3.3. Controller SSP

The setting for the conveying time and the line clear time are made via the keys (A1: “change-over” key, A2: “arrow key”) on the front of the control system. The values which have been set will be displayed on the display (B). The values which have been set are maintained after the machine has been shut off.

3 LEDs indicate the respective modes of operation: pulse duration (C), time interval (D), without function (E).

The pulse duration can be set to 0.5, 1.0 or 1.5 seconds.

The time interval can be set from 5 to 20 seconds.

When the unit is switched on all LEDs blink and the software version is displayed.

SM4-630

A1A2

Controller SSP

Functional description 25

Page 26

Image 26

Sterling SSPET 5 operating instructions SSPET5 3.3. Controller SSP, Functional description

Contents

SM4-630 Sterling Material ProcessingOperating Instructions Single Conveyor Unit For Powder SSPET Parts and Service Department Sales and Contracting DepartmentTelephone 800 Edition 02/01 Sterling order confirmation no Technical serviceSSPET5 Sterling Material Processing SM4-630SSPET5 2. Assembly instructions Table of contents1. Safety instructions 3. Functional descriptionSSPET5 5. Maintenance 6. Technical data 7. Parts list 8. AccessoriesSSPET5 1. Safety instructionsSafety instructions SSPET5 1.1. Warnings and symbols Safety instructionsSafety instructions ∙ ∙ ∙ ∙ ∙ ∙SSPET5 1.2. Explanations and information This avoids injury and damage to equipment SSPET5 1.3. For your safetySafety instructions Safety instructions SSPET5SSPET5 ∙ ∙ ∙ ∙Safety instructions SSPET5 1.4. For the operating safety of the equipment SSPET5 2. Assembly instructionsAssembly instructions Assembly instructions SSPET5 2.1. AssemblyThe equipment is delivered as a complete assembly SSPET5 Assembly instructionsAssembly SM4-630 Connect the inner pipe with the straight end to a flexible hose SSPET5 2.2. Mounting the suction pipe MVAssembly instructions The operating voltage is 230 V/50 Hz Special voltages on request SSPET5 2.3. Electrical connectionAssembly instructions Insert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller SSPET5 2.3.1. Installation of the “flap switch” signal line2.3.2. Installation of the signal line of the SKW optional Assembly instructionsThis work must be carried out by qualified personnel only Assembly instructionsSSPET5 Assembly instructions SSPET5 2.4. Compressed-air supplyFor operating the cleaning unit, a compressed-air supply is necessary SSPET5 3. Functional descriptionFunctional description Functional description SSPET5 3.1. GeneralThe filter-cleaning process takes place during the conveying process Functional description SSPET5 3.2. Controller SSEThe emptying time consists of 8 seconds Functional description An “E” appears in the display and an error numberSSPET5 SSPET5 3.3. Controller SSP Functional descriptionSSPET5 4. Putting into operationPutting into operation Putting into operation SSPET5 4.1. Checking the pipe systemRemove the flexible hose from the connected material takeup If the conditions points 3 + 4 are met SSPET5 4.2. Adjusting the suction pipesIf the conditions points 3 + 4 are not met Putting into operationThe turbine is running but no material is being conveyed SSPET5 4.3. Setting the controller SSESetting the conveying time The conveying capacity is too lowIf no line clear valve has been installed enter “0 SSPET5 Setting the line clear timethe “change-over” key Press the “arrow key” andSetting the time interval SSPET5 4.4. Setting the controller SSPSetting the pulse duration Press the “arrow key” the “change-over” keyPutting into operation 4.6. Alarm Messages displayed on the controller SSESSPET5 4.5. Initial conveying operations Putting into operation The following error messages can be displayedSSPET5 Putting into operation SSPET5 4.7. Alarm Messages displayed on the controller SSP4.8. Switching off the unit SSPET5 5. MaintenanceMaintenance SSPET5 Please observe the maintenance intervalsMaintenance Daily SSPET5 5.1. Maintenance intervalsMaintenance Maintenance 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unitSSPET5 5.2. Servicing the conveyor Maintenance InstallationRemoval SSPET5Assembly sealing ring SSPET5 5.2.2. Changing the sealing ring of the outlet flapMaintenance SM4-630SSPET5 5.2.3. Adjusting the flap switch MaintenanceSSPET5 SM4-630 SSPET5 5.3. Replacing carbon brushes at turbineMaintenance SSPET5 Installation MaintenanceTechnical data 6. Technical dataOptional Features Basic VersionSM4-630 SSPET5 Dimension SheetTechnical data This parts list is only for the use of trained personnel only 7. Parts listParts list SSPET5SM4-630 SSPET5 SSPET5Parts list Parts list Order noDesignation SSPET5SSPET5 8. AccessoriesAccessories SM4-630