Manuals / Sterling / Marine Equipment / Marine Battery

Sterling SSPET 5 operating instructions SSPET5 4.7. Alarm Messages displayed on the controller SSP

Models: SSPET 5

1 50

Download 50 pages 3.15 Kb

Page 35

Image 35

SSPET5

4.7. Alarm Messages displayed on the controller SSP

If a disturbance occurs in the unit, an alarm message will be issued.

“E2"

An “E” appears in the display and an error number.

If the control system becomes too hot during operation (>70°C) (158°F) the “E2" alarm message is displayed and the unit is switched off.

Ensure that the control system is sufficient cooled.

The unit starts automatically after the cooling down phase.

4.8. Switching off the unit

Disconnect the unit from mains supply by the device plug.

SM4-630

Putting into operation 34

Page 35

Image 35

Sterling SSPET 5 operating instructions SSPET5 4.7. Alarm Messages displayed on the controller SSP, Switching off the unit

Contents

SM4-630 Sterling Material ProcessingOperating Instructions Single Conveyor Unit For Powder SSPET Sales and Contracting Department Parts and Service DepartmentSM4-630 Technical serviceSSPET5 Sterling Material Processing Telephone 800 Edition 02/01 Sterling order confirmation noSSPET5 3. Functional description Table of contents1. Safety instructions 2. Assembly instructions6. Technical data 7. Parts list 8. Accessories SSPET5 5. MaintenanceSSPET5 1. Safety instructionsSafety instructions Safety instructions SSPET5 1.1. Warnings and symbolsSafety instructions ∙ ∙ ∙ ∙ ∙ ∙SSPET5 1.2. Explanations and information This avoids injury and damage to equipment SSPET5 1.3. For your safetySafety instructions SSPET5 Safety instructionsSSPET5 ∙ ∙ ∙ ∙Safety instructions SSPET5 1.4. For the operating safety of the equipment SSPET5 2. Assembly instructionsAssembly instructions Assembly instructions SSPET5 2.1. AssemblyThe equipment is delivered as a complete assembly SSPET5 Assembly instructionsAssembly SM4-630 Connect the inner pipe with the straight end to a flexible hose SSPET5 2.2. Mounting the suction pipe MVAssembly instructions The operating voltage is 230 V/50 Hz Special voltages on request SSPET5 2.3. Electrical connectionAssembly instructions Assembly instructions SSPET5 2.3.1. Installation of the “flap switch” signal line2.3.2. Installation of the signal line of the SKW optional Insert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controllerThis work must be carried out by qualified personnel only Assembly instructionsSSPET5 Assembly instructions SSPET5 2.4. Compressed-air supplyFor operating the cleaning unit, a compressed-air supply is necessary SSPET5 3. Functional descriptionFunctional description Functional description SSPET5 3.1. GeneralThe filter-cleaning process takes place during the conveying process Functional description SSPET5 3.2. Controller SSEThe emptying time consists of 8 seconds Functional description An “E” appears in the display and an error numberSSPET5 Functional description SSPET5 3.3. Controller SSPSSPET5 4. Putting into operationPutting into operation Putting into operation SSPET5 4.1. Checking the pipe systemRemove the flexible hose from the connected material takeup Putting into operation SSPET5 4.2. Adjusting the suction pipesIf the conditions points 3 + 4 are not met If the conditions points 3 + 4 are metThe conveying capacity is too low SSPET5 4.3. Setting the controller SSESetting the conveying time The turbine is running but no material is being conveyedPress the “arrow key” and SSPET5 Setting the line clear timethe “change-over” key If no line clear valve has been installed enter “0the “change-over” key SSPET5 4.4. Setting the controller SSPSetting the pulse duration Press the “arrow key” Setting the time intervalPutting into operation 4.6. Alarm Messages displayed on the controller SSESSPET5 4.5. Initial conveying operations Putting into operation The following error messages can be displayedSSPET5 Putting into operation SSPET5 4.7. Alarm Messages displayed on the controller SSP4.8. Switching off the unit SSPET5 5. MaintenanceMaintenance SSPET5 Please observe the maintenance intervalsMaintenance Daily SSPET5 5.1. Maintenance intervalsMaintenance Maintenance 5.2.1. Cleaning/replacing the filter cartridges of the cleaning unitSSPET5 5.2. Servicing the conveyor SSPET5 InstallationRemoval MaintenanceSM4-630 SSPET5 5.2.2. Changing the sealing ring of the outlet flapMaintenance Assembly sealing ringMaintenance SSPET5 5.2.3. Adjusting the flap switchSSPET5 SM4-630 SSPET5 5.3. Replacing carbon brushes at turbineMaintenance Maintenance SSPET5 InstallationBasic Version 6. Technical dataOptional Features Technical dataSM4-630 SSPET5 Dimension SheetTechnical data SSPET5 7. Parts listParts list This parts list is only for the use of trained personnel onlySM4-630 SSPET5 SSPET5Parts list SSPET5 Order noDesignation Parts listSM4-630 8. AccessoriesAccessories SSPET5