Manuals
/
Sterling
/
Marine Equipment
/
Marine Battery
Sterling
SSPET 5 operating instructions Sterling Material Processing, SM4-630
Models:
SSPET 5
1
1
50
50
Download
50 pages
3.15 Kb
1
2
3
4
5
6
7
8
<
>
Install
Parts list
Error messages
Dimension
Maintenance
Assembly instructions
An “E” appears in the display and an error number
SSPET5 4.2. Adjusting the suction pipes
SSPET5 4.3. Setting the controller SSE
For operating the cleaning unit, a compressed-air supply is necessary
Page 1
Image 1
Operating Instructions
Single Conveyor Unit
For Powder
SSPET 5
SM4-630
Sterling Material Processing
Page 2
Page 1
Image 1
Page 2
Contents
Operating Instructions Single Conveyor Unit For Powder SSPET
Sterling Material Processing
SM4-630
Sales and Contracting Department
Parts and Service Department
SSPET5 Sterling Material Processing
Technical service
Telephone 800 Edition 02/01 Sterling order confirmation no
SM4-630
SSPET5
1. Safety instructions
Table of contents
2. Assembly instructions
3. Functional description
6. Technical data 7. Parts list 8. Accessories
SSPET5 5. Maintenance
Safety instructions
1. Safety instructions
SSPET5
Safety instructions
SSPET5 1.1. Warnings and symbols
SSPET5 1.2. Explanations and information
∙ ∙ ∙ ∙ ∙ ∙
Safety instructions
Safety instructions
SSPET5 1.3. For your safety
This avoids injury and damage to equipment
SSPET5
Safety instructions
Safety instructions
∙ ∙ ∙ ∙
SSPET5
SSPET5 1.4. For the operating safety of the equipment
Assembly instructions
2. Assembly instructions
SSPET5
The equipment is delivered as a complete assembly
SSPET5 2.1. Assembly
Assembly instructions
Assembly SM4-630
Assembly instructions
SSPET5
Assembly instructions
SSPET5 2.2. Mounting the suction pipe MV
Connect the inner pipe with the straight end to a flexible hose
Assembly instructions
SSPET5 2.3. Electrical connection
The operating voltage is 230 V/50 Hz Special voltages on request
2.3.2. Installation of the signal line of the SKW optional
SSPET5 2.3.1. Installation of the “flap switch” signal line
Insert the appliance plug of the “flap switch” signal line into the “flap switch” con- nector A on the lower side of the controller
Assembly instructions
SSPET5
Assembly instructions
This work must be carried out by qualified personnel only
For operating the cleaning unit, a compressed-air supply is necessary
SSPET5 2.4. Compressed-air supply
Assembly instructions
Functional description
3. Functional description
SSPET5
The filter-cleaning process takes place during the conveying process
SSPET5 3.1. General
Functional description
The emptying time consists of 8 seconds
SSPET5 3.2. Controller SSE
Functional description
SSPET5
An “E” appears in the display and an error number
Functional description
Functional description
SSPET5 3.3. Controller SSP
Putting into operation
4. Putting into operation
SSPET5
Remove the flexible hose from the connected material takeup
SSPET5 4.1. Checking the pipe system
Putting into operation
If the conditions points 3 + 4 are not met
SSPET5 4.2. Adjusting the suction pipes
If the conditions points 3 + 4 are met
Putting into operation
Setting the conveying time
SSPET5 4.3. Setting the controller SSE
The turbine is running but no material is being conveyed
The conveying capacity is too low
the “change-over” key
SSPET5 Setting the line clear time
If no line clear valve has been installed enter “0
Press the “arrow key” and
Setting the pulse duration Press the “arrow key”
SSPET5 4.4. Setting the controller SSP
Setting the time interval
the “change-over” key
SSPET5 4.5. Initial conveying operations
4.6. Alarm Messages displayed on the controller SSE
Putting into operation
SSPET5
The following error messages can be displayed
Putting into operation
4.8. Switching off the unit
SSPET5 4.7. Alarm Messages displayed on the controller SSP
Putting into operation
Maintenance
5. Maintenance
SSPET5
Maintenance
Please observe the maintenance intervals
SSPET5
Maintenance
SSPET5 5.1. Maintenance intervals
Daily
SSPET5 5.2. Servicing the conveyor
5.2.1. Cleaning/replacing the filter cartridges of the cleaning unit
Maintenance
Removal
Installation
Maintenance
SSPET5
Maintenance
SSPET5 5.2.2. Changing the sealing ring of the outlet flap
Assembly sealing ring
SM4-630
Maintenance
SSPET5 5.2.3. Adjusting the flap switch
Maintenance
SSPET5 5.3. Replacing carbon brushes at turbine
SSPET5 SM4-630
Maintenance
SSPET5 Installation
Optional Features
6. Technical data
Technical data
Basic Version
Technical data
SSPET5 Dimension Sheet
SM4-630
Parts list
7. Parts list
This parts list is only for the use of trained personnel only
SSPET5
Parts list
SSPET5 SSPET5
SM4-630
Designation
Order no
Parts list
SSPET5
Accessories
8. Accessories
SSPET5
SM4-630