Netra 1290 Server Installation Guide | Sun Microsystems instruction

Netra™ 1290 Server Installation

Guide

Sun Microsystems, Inc.

www.sun.com

Part No. 819-4372-10

May 2006, Revision A

Submit comments about this document at: http://www.sun.com/hwdocs/feedback

Image 1

Sun Microsystems manual Netra 1290 Server Installation Guide

Contents

Netra 1290 Server Installation Guide Please Recycle Contents Netra 1290 Server Connections Setting Up 39 Setup Process Figures System Controller and I/O Assembly Locations Tables Viii Netra 1290 Server Installation Guide May How This Document Is Organized Using Unix Commands Typographic Conventions Shell Prompts Documentation, Support, and Training Related DocumentationThird-Party Web Sites Sun Welcomes Your Comments To Unpack the Server Unpacking the Server 1Opening the Shipping Carton Remove and unpack the shipping kit 2Removing the Carton Pieces Remove the outer carton Remove the internal saddle Installing Slide Rails N F I R E Adjusting the Slide Rail Assembly To Install the Inner Rails on the Server Spring clip should engage Repeat through for the second inner rail To Prepare the Rails for 2-Post Installations To Install the Slide Rail Assemblies in the Bottom Position To Install the Slide Rail Assemblies in the Top Position To Install the Slide Rail Assemblies in the Bottom Position Front bracket Rear bracket Secured to outer cabinet holes To Install the Slide Rail Assemblies in the Top Position Netra 1290 Server Installation Guide May To Prepare to Install the Server in the Cabinet Installing the Server in a CabinetSecure the front bracket with two No -32 UNF screws Remove the shipping cradle bolts Figure Repeat Step a and Step b for the second front bezel door 9Removing the Shipping Cradle Bolts To Mount the Server in the Cabinet Latches on each side must click out, locking the rails Outer rails Inner rails 12Removing the Shipping Cradle 13Pushing the Server Into the System Cabinet Retract the cabinet stabilization mechanism as required To Install the Lock Nuts Installing Slide Rail Lock NutsReattach the front doors of the server 15Inserting and Tightening the Spacers Slide the server into the system cabinet To Install the CMA-Lite on To Install the CMA-800 on Installing the Cable Management Arm 18CMA-Lite Cable Management Arm To Install the CMA-Lite To Install the CMA-800 20Upper and Lower Pivot Bracket Mounting Holes Hinge pin Upper pivot bracket Upper CMA arm Hinge pin Lower pivot bracket Lower CMA arm Slide rail Left hand T-bracket Slide rail Right hand T-bracket 25Attaching the Upper and Lower CMA Arms to the T-Bracket To Connect the Power Cables Connecting Power Cables Connecting Consoles to the System Controller Set up the system console To Connect the Initial Administrative Console Set up the chosen administrative console To Connect the Administrative Console Installing Additional Hardware Connecting the I/O AssembliesTo Connect the I/O Assemblies Installing Additional Peripheral Devices Setup Process Setting Up On/Standby Switch Setting Up the HardwareTo Install and Cable the Hardware Disabling Operation of the On/Standby Switch Powering On the ServerTo Power On Using the On/Standby Switch To disable the On/Standby switch, use the setupsc command To Power On Using the LOM poweron Command Bringing the Server to Standby ModeAt the lom prompt, type For an abrupt power off, type To Bring the System to Standby Mode From the LOM PortPress the left side of the system On/Standby switch At the system prompt, type To Set Up the Password Setting Up the ServerAt the LOM prompt, type the SC password command To Set the Date and Time At the LOM prompt, type setupnetwork To Configure Network ParametersAnswer the questions in the script To Install and Boot the Solaris Operating System Installing and Booting the Solaris Operating SystemAccess the LOM prompt To power on the server, type poweron Installing the Lights Out Management PackagesIf necessary, install the Solaris Operating System As superuser, type To Install the LOM Drivers ’type=ddipseudoname=lomp To Install the LOM Manual Pages To Install the LOM Utility # pkgadd -d . SUNWlomm Netra 1290 Server Installation Guide May External I/O Connection Locations Netra 1290 Server Connections Figure A-1External I/O Connection Locations PCI+ Ibssc Assemblies SCSI3 Scsi Connector Scsi Implementation Alarms Port NET0/NET1 Ethernet Ports Table A-3Alarms Service Port Connector Pinout NET 10/100BASE-T LOM Ethernet Port Twisted-Pair Ethernet Cable-Type Connectivity LOM Serial a and Serial B Ports LOM Serial a Serial B Using a DB-9 Adapter for Your Serial Link Using a DB-25 Adapter for Your Serial Link Netra 1290 Server Installation Guide May Index Setupnetwork command