Sun Welcomes Your Comments | Sun Microsystems 1290 specification

Sun Welcomes Your Comments

Sun is interested in improving its documentation and welcomes your comments and suggestions. You can submit your comments by going to:

http://www.sun.com/hwdocs/feedback

Please include the title and part number of your document with your feedback:

Netra 1290 Server Installation Guide, part number 819-4372-10

xii Netra 1290 Server Installation Guide • May 2006

Image 12

Sun Microsystems 1290 manual Sun Welcomes Your Comments

Contents

Netra 1290 Server Installation Guide Please Recycle Contents Setting Up 39 Setup Process Netra 1290 Server Connections Figures System Controller and I/O Assembly Locations Tables Viii Netra 1290 Server Installation Guide May Using Unix Commands How This Document Is Organized Shell Prompts Typographic Conventions Related Documentation Documentation, Support, and TrainingThird-Party Web Sites Sun Welcomes Your Comments Unpacking the Server To Unpack the Server Remove and unpack the shipping kit 1Opening the Shipping Carton Remove the outer carton 2Removing the Carton Pieces Installing Slide Rails Remove the internal saddle Adjusting the Slide Rail Assembly N F I R E To Install the Inner Rails on the Server Spring clip should engage To Prepare the Rails for 2-Post Installations Repeat through for the second inner rail To Install the Slide Rail Assemblies in the Bottom Position To Install the Slide Rail Assemblies in the Top Position To Install the Slide Rail Assemblies in the Bottom Position Front bracket Rear bracket Secured to outer cabinet holes To Install the Slide Rail Assemblies in the Top Position Netra 1290 Server Installation Guide May Installing the Server in a Cabinet To Prepare to Install the Server in the CabinetSecure the front bracket with two No -32 UNF screws Repeat Step a and Step b for the second front bezel door Remove the shipping cradle bolts Figure To Mount the Server in the Cabinet 9Removing the Shipping Cradle Bolts Latches on each side must click out, locking the rails Outer rails Inner rails 12Removing the Shipping Cradle Retract the cabinet stabilization mechanism as required 13Pushing the Server Into the System Cabinet Installing Slide Rail Lock Nuts To Install the Lock NutsReattach the front doors of the server Slide the server into the system cabinet 15Inserting and Tightening the Spacers Installing the Cable Management Arm To Install the CMA-Lite on To Install the CMA-800 on To Install the CMA-Lite 18CMA-Lite Cable Management Arm To Install the CMA-800 20Upper and Lower Pivot Bracket Mounting Holes Hinge pin Upper pivot bracket Upper CMA arm Hinge pin Lower pivot bracket Lower CMA arm Slide rail Left hand T-bracket Slide rail Right hand T-bracket 25Attaching the Upper and Lower CMA Arms to the T-Bracket Connecting Power Cables To Connect the Power Cables Connecting Consoles to the System Controller To Connect the Initial Administrative Console Set up the system console To Connect the Administrative Console Set up the chosen administrative console Connecting the I/O Assemblies Installing Additional HardwareTo Connect the I/O Assemblies Installing Additional Peripheral Devices Setting Up Setup Process Setting Up the Hardware On/Standby SwitchTo Install and Cable the Hardware Powering On the Server Disabling Operation of the On/Standby SwitchTo Power On Using the On/Standby Switch To disable the On/Standby switch, use the setupsc command Bringing the Server to Standby Mode To Power On Using the LOM poweron CommandAt the lom prompt, type To Bring the System to Standby Mode From the LOM Port For an abrupt power off, typePress the left side of the system On/Standby switch At the system prompt, type Setting Up the Server To Set Up the PasswordAt the LOM prompt, type the SC password command To Set the Date and Time To Configure Network Parameters At the LOM prompt, type setupnetworkAnswer the questions in the script Installing and Booting the Solaris Operating System To Install and Boot the Solaris Operating SystemAccess the LOM prompt Installing the Lights Out Management Packages To power on the server, type poweronIf necessary, install the Solaris Operating System To Install the LOM Drivers As superuser, type ’type=ddipseudoname=lomp To Install the LOM Utility To Install the LOM Manual Pages # pkgadd -d . SUNWlomm Netra 1290 Server Installation Guide May Netra 1290 Server Connections External I/O Connection Locations PCI+ Ibssc Assemblies Figure A-1External I/O Connection Locations Scsi Connector SCSI3 Alarms Port Scsi Implementation Table A-3Alarms Service Port Connector Pinout NET0/NET1 Ethernet Ports 10/100BASE-T LOM Ethernet Port NET LOM Serial a and Serial B Ports Twisted-Pair Ethernet Cable-Type Connectivity LOM Serial a Serial B Using a DB-25 Adapter for Your Serial Link Using a DB-9 Adapter for Your Serial Link Netra 1290 Server Installation Guide May Index Setupnetwork command