Remove the shipping cradle bolts Figure | Sun Microsystems 1290

c. Repeat Step a and Step b for the second front bezel door.

FIGURE 1-8Releasing the Door Hinge Mechanism

2.Remove the shipping cradle bolts (FIGURE 1-9).

The bolts secure the orange metal shipping cradle to the wooden pallet.

16 Netra 1290 Server Installation Guide • May 2006

Image 28

Sun Microsystems 1290 Repeat Step a and Step b for the second front bezel door, Remove the shipping cradle bolts Figure

Contents

Netra 1290 Server Installation Guide Please Recycle Contents Setting Up 39 Setup Process Netra 1290 Server Connections Figures System Controller and I/O Assembly Locations Tables Viii Netra 1290 Server Installation Guide May Using Unix Commands How This Document Is Organized Shell Prompts Typographic Conventions Documentation, Support, and Training Related DocumentationThird-Party Web Sites Sun Welcomes Your Comments Unpacking the Server To Unpack the Server Remove and unpack the shipping kit 1Opening the Shipping Carton Remove the outer carton 2Removing the Carton Pieces Installing Slide Rails Remove the internal saddle Adjusting the Slide Rail Assembly N F I R E To Install the Inner Rails on the Server Spring clip should engage To Prepare the Rails for 2-Post Installations Repeat through for the second inner rail To Install the Slide Rail Assemblies in the Bottom Position To Install the Slide Rail Assemblies in the Top Position To Install the Slide Rail Assemblies in the Bottom Position Front bracket Rear bracket Secured to outer cabinet holes To Install the Slide Rail Assemblies in the Top Position Netra 1290 Server Installation Guide May To Prepare to Install the Server in the Cabinet Installing the Server in a CabinetSecure the front bracket with two No -32 UNF screws Repeat Step a and Step b for the second front bezel door Remove the shipping cradle bolts Figure To Mount the Server in the Cabinet 9Removing the Shipping Cradle Bolts Latches on each side must click out, locking the rails Outer rails Inner rails 12Removing the Shipping Cradle Retract the cabinet stabilization mechanism as required 13Pushing the Server Into the System Cabinet To Install the Lock Nuts Installing Slide Rail Lock NutsReattach the front doors of the server Slide the server into the system cabinet 15Inserting and Tightening the Spacers Installing the Cable Management Arm To Install the CMA-Lite on To Install the CMA-800 on To Install the CMA-Lite 18CMA-Lite Cable Management Arm To Install the CMA-800 20Upper and Lower Pivot Bracket Mounting Holes Hinge pin Upper pivot bracket Upper CMA arm Hinge pin Lower pivot bracket Lower CMA arm Slide rail Left hand T-bracket Slide rail Right hand T-bracket 25Attaching the Upper and Lower CMA Arms to the T-Bracket Connecting Power Cables To Connect the Power Cables Connecting Consoles to the System Controller To Connect the Initial Administrative Console Set up the system console To Connect the Administrative Console Set up the chosen administrative console Installing Additional Hardware Connecting the I/O AssembliesTo Connect the I/O Assemblies Installing Additional Peripheral Devices Setting Up Setup Process On/Standby Switch Setting Up the HardwareTo Install and Cable the Hardware Powering On the Server Disabling Operation of the On/Standby SwitchTo Power On Using the On/Standby Switch To disable the On/Standby switch, use the setupsc command To Power On Using the LOM poweron Command Bringing the Server to Standby ModeAt the lom prompt, type To Bring the System to Standby Mode From the LOM Port For an abrupt power off, typePress the left side of the system On/Standby switch At the system prompt, type Setting Up the Server To Set Up the PasswordAt the LOM prompt, type the SC password command To Set the Date and Time At the LOM prompt, type setupnetwork To Configure Network ParametersAnswer the questions in the script To Install and Boot the Solaris Operating System Installing and Booting the Solaris Operating SystemAccess the LOM prompt To power on the server, type poweron Installing the Lights Out Management PackagesIf necessary, install the Solaris Operating System To Install the LOM Drivers As superuser, type ’type=ddipseudoname=lomp To Install the LOM Utility To Install the LOM Manual Pages # pkgadd -d . SUNWlomm Netra 1290 Server Installation Guide May Netra 1290 Server Connections External I/O Connection Locations PCI+ Ibssc Assemblies Figure A-1External I/O Connection Locations Scsi Connector SCSI3 Alarms Port Scsi Implementation Table A-3Alarms Service Port Connector Pinout NET0/NET1 Ethernet Ports 10/100BASE-T LOM Ethernet Port NET LOM Serial a and Serial B Ports Twisted-Pair Ethernet Cable-Type Connectivity LOM Serial a Serial B Using a DB-25 Adapter for Your Serial Link Using a DB-9 Adapter for Your Serial Link Netra 1290 Server Installation Guide May Index Setupnetwork command