Remove the outer carton | Sun Microsystems 1290 manual

Shipping kit

Outer carton

Internal saddle

FIGURE 1-2Removing the Carton Pieces

6.Remove the outer carton.

See FIGURE 1-2.

Chapter 1 Unpacking and Installing the Server 3

Image 15

Sun Microsystems 1290 manual Remove the outer carton, 2Removing the Carton Pieces

Contents

Netra 1290 Server Installation Guide Please Recycle Contents Netra 1290 Server Connections Setting Up 39 Setup Process Figures System Controller and I/O Assembly Locations Tables Viii Netra 1290 Server Installation Guide May How This Document Is Organized Using Unix Commands Typographic Conventions Shell Prompts Related Documentation Documentation, Support, and TrainingThird-Party Web Sites Sun Welcomes Your Comments To Unpack the Server Unpacking the Server 1Opening the Shipping Carton Remove and unpack the shipping kit 2Removing the Carton Pieces Remove the outer carton Remove the internal saddle Installing Slide Rails N F I R E Adjusting the Slide Rail Assembly To Install the Inner Rails on the Server Spring clip should engage Repeat through for the second inner rail To Prepare the Rails for 2-Post Installations To Install the Slide Rail Assemblies in the Bottom Position To Install the Slide Rail Assemblies in the Top Position To Install the Slide Rail Assemblies in the Bottom Position Front bracket Rear bracket Secured to outer cabinet holes To Install the Slide Rail Assemblies in the Top Position Netra 1290 Server Installation Guide May Installing the Server in a Cabinet To Prepare to Install the Server in the CabinetSecure the front bracket with two No -32 UNF screws Remove the shipping cradle bolts Figure Repeat Step a and Step b for the second front bezel door 9Removing the Shipping Cradle Bolts To Mount the Server in the Cabinet Latches on each side must click out, locking the rails Outer rails Inner rails 12Removing the Shipping Cradle 13Pushing the Server Into the System Cabinet Retract the cabinet stabilization mechanism as required Installing Slide Rail Lock Nuts To Install the Lock NutsReattach the front doors of the server 15Inserting and Tightening the Spacers Slide the server into the system cabinet To Install the CMA-Lite on To Install the CMA-800 on Installing the Cable Management Arm 18CMA-Lite Cable Management Arm To Install the CMA-Lite To Install the CMA-800 20Upper and Lower Pivot Bracket Mounting Holes Hinge pin Upper pivot bracket Upper CMA arm Hinge pin Lower pivot bracket Lower CMA arm Slide rail Left hand T-bracket Slide rail Right hand T-bracket 25Attaching the Upper and Lower CMA Arms to the T-Bracket To Connect the Power Cables Connecting Power Cables Connecting Consoles to the System Controller Set up the system console To Connect the Initial Administrative Console Set up the chosen administrative console To Connect the Administrative Console Connecting the I/O Assemblies Installing Additional HardwareTo Connect the I/O Assemblies Installing Additional Peripheral Devices Setup Process Setting Up Setting Up the Hardware On/Standby SwitchTo Install and Cable the Hardware To disable the On/Standby switch, use the setupsc command Powering On the ServerDisabling Operation of the On/Standby Switch To Power On Using the On/Standby Switch Bringing the Server to Standby Mode To Power On Using the LOM poweron CommandAt the lom prompt, type At the system prompt, type To Bring the System to Standby Mode From the LOM PortFor an abrupt power off, type Press the left side of the system On/Standby switch To Set the Date and Time Setting Up the ServerTo Set Up the Password At the LOM prompt, type the SC password command To Configure Network Parameters At the LOM prompt, type setupnetworkAnswer the questions in the script Installing and Booting the Solaris Operating System To Install and Boot the Solaris Operating SystemAccess the LOM prompt Installing the Lights Out Management Packages To power on the server, type poweronIf necessary, install the Solaris Operating System As superuser, type To Install the LOM Drivers ’type=ddipseudoname=lomp To Install the LOM Manual Pages To Install the LOM Utility # pkgadd -d . SUNWlomm Netra 1290 Server Installation Guide May External I/O Connection Locations Netra 1290 Server Connections Figure A-1External I/O Connection Locations PCI+ Ibssc Assemblies SCSI3 Scsi Connector Scsi Implementation Alarms Port NET0/NET1 Ethernet Ports Table A-3Alarms Service Port Connector Pinout NET 10/100BASE-T LOM Ethernet Port Twisted-Pair Ethernet Cable-Type Connectivity LOM Serial a and Serial B Ports LOM Serial a Serial B Using a DB-9 Adapter for Your Serial Link Using a DB-25 Adapter for Your Serial Link Netra 1290 Server Installation Guide May Index Setupnetwork command