Toro 3000D manual Specifications

Specifications

Deck Configuration: Out front deck with a right hand trim offset. Four individual chambers jointed for articula- tion. One blade per chamber.

Cutting Width: 82 inches (2.1 m).

Chamber Housing: 12 GA. steel, 4.5 inch (114 mm) deep, welded construction and reinforced with 10 GA high strength formed plates.

Height–of–Cut (HOC): 1 inch (25 mm) to 4 inch (102 mm) by 1/4 inch (6 mm) increments.

Blade Size: Four 22 inch (559 mm) long by 2.50 inch (64

mm)wide by .25 inch (6 mm) thick heat treated steel with formed parallel sails.

Blade Overlap: 2 inch (51 mm) in the flat configuration.

Blade Drive: Hydraulic drive via a PTO driven high effi- ciency gear pump on the traction unit integrated hydro- static transaxle (IHT). Four integrated spindle motors operated in a series configuration through SAE–10 (.625) high pressure wear resistant hoses with high den- sity polyethylene protective tubing. Spindle motor is a high efficiency pressure balanced gear motor with a di- rect drive to the spindle shaft operating in a constant wet lubrication on two Teflon coated journal bearings. Welded blade retainers mounted through a tapered joint with a 2 inch (51 mm) high outer shield to protect spindle seals. Hydraulic braking valve set to 600 PSI (41 Bar) to achieve a complete blade stopping time of 5 seconds from full engine (PTO) speed.

Blade Speed: 15,724 feet (4,793 m) per minute tip speed (2730 rpm spindle speed) at 2795 rpm on diesel models and 3275 on gas models.

Suspension & Castor Wheels: Five front castors and three rear castors, consisting of 8 inch (203 mm) pneu- matic wheels with sealed ball bearings. One rear link suspended from the right lift arm. Hydraulic counter bal- ance and lift system designed integral with deck for max- imum floatation.

Anti–Scalp Features: 11 inch (279 mm) diameter anti scalp cups located .75 inch (19 mm) below each blade. Adjacent chambers pivot freely about two independent 60_ opposed hinges down –20_and up +20_. 1 inch (25 mm) diameter anti–scalp/wear skids located on each outside chamber.

Discharge: Evenly dispersed rear discharge between the outside width of the deck with partial recycling rear baffles.

Lift/Transport: Stainless steel cables from outside chambers to nearest lift arm actuated via a lever on the lift arms. Complete deck is lifted via the traction unit lift system.

Counter–Balance:Recommended operating counter balance pressure of 125 PSI (9 Bar) set by an adjustable counter balance valve on the traction unit.

Overhang/Trim: Deck is offset to the right of the traction unit to provide overhang of 21 inch (533 mm) on the right and 8.25 inch (210 mm) on the left with deck in a flat con- figuration. Uncut circle is 16 inch (406 mm) on right with no brakes.

Covers: No complete deck covers required. Hydraulic hoses to be covered per ANSI/ISO standards.

Connect/Disconnect: Use existing GM 3000 style of quick attach lift arm system. For ease of cleaning and maintaining oil cleanliness, the hydraulic lines use flush face quick couplers for pressure supply line, return line, braking sense line, and motor case drain line.

Sound Levels: Operator ear to be  90 dBA per SAE measuring standards.

Safety: Deck and traction unit to comply with ANSI B71.4–1990 and CE compliance.

Productivity: Mows up to 4.6 acre (1.86 hectare) per hour at 5.5 mph (9 km/hr)

Approach Angle: Minimum approach angle (for trailer- ing) of 11.5 at highest HOC setting.

Weight: 745 lbs (338 Kg).

Specifications and design subject to change without notice.

Contour 82 Cutting Unit Page 10 – 2 Groundsmaster 3000/3000–D