Communication, RS232, Comm Setting, Slave | Toshiba KV-HD01A

5.5 COMMUNICATION

The COMMUNICATION option is used to configure status of the communication port when the connected with an external device.

MAIN MENU

TIME/ TITLE RECORD TIMER RECORD ALARM COMMUNICATION DISK

SYSTEM

GO TO COMM PAGE

RS232:

COMM SETTING

RS232		: SLAVE
NET	ENABLE	: OFF
NET SETTING		: SET
MAIN PAGE
SET RS232

The RS232 option is used to determine the activation/ deactivation of the RS232 communication port for externally triggered recording. To record video into the hard-disk drive connect the REC exposure contact on the rear panel of the DVR to the switch used to activate the alarm.

MASTER: Sets the KV-HD01A as the master device.

SLAVE: Sets the KV-HD01A as the slave device.

NET ENABLE is used to allow remote users viewing privileges over a network or IP. OFF: Ethernet capability is turned off

ON: Ethernet capability is turned on

NET SETTING is used to set the IP, MASK, and GATEWAY address of the KV-HD01A. SET: Sets the IP,MASK, and GATEWAY addresses of the KV-HD01A

36

Image 37

Toshiba KV-HD01A manual Communication, Comm Setting, Slave, NET Enable OFF NET Setting SET Main SET RS232

Contents

Installation Operating Manual Table of Contents Limited Warranty SpecificationsMain Menu Apendix 4. -- Network Viewing FCC Notice Safety Precautions Manufacturer’s instruction Graphic symbol definitions Symbol Meaning Important Safety InstructionsIndication definitions Meaning Disclaimer Observe the following when installing Daily or weekly Maintenance Important PrecautionsCopyrights Save Original Packing Materials Product Features Product FeaturesProduct Introduction Front View Description of the FRONT/REAR View Indicator of Timer Recording Mode Indicator of Alarm Recording ModeIndicator of Hard Disk Status Power Indicator Rear View Terminal Block Connecting with a Single Camera or a Quad Processor InstallationConnecting with a Multiplexer Basic Connection Quality High Ntsc System InformationRate 6 HR Size POS Updating System Software Video format NTSC/PAL selection Set up the REC Time Mode when a multiplexer is connected Configuring Recording SettingsBasic Operations Ntsc System Manual Recording Recording OperationsPAL System Start END Timer Recording Main SET REC Timer REC Schedule Start END TIMER---------------------------- SETREC Enable Timer Main Timer REC Enable Externally triggered Recording Alarm Recording60F/S Place Operation Status Playback OperationsFast Forward/Reverse Play Back Picture-by-picture Slow Forward/Reverse Play Back Recorded Video from a HDD of the mobile rack Search OperationsFull List Search Search Full List Alarm List Time Search MM DD Year HH MM Alarm list SearchTime Search Search Backup Operations Data BackupSystem GO to Disk Disk Setting Reformat HD 3 Usage Main Backup ALL to HD Disk Setting Reformat HD 3 Usage Alarm Select Main Backup Alarm to HDMain Backup Part to HD Total 41 M Ready to GO OK Cancel Save ENTER/SAVE button Archive Clips into Floppy Disk Key Lock OperationSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Right/Left buttons Main Menu Title Setting Time SettingTIME/ Title Title Stamp Timer Record TimerREC Schedule Start END 0600-1600 1200-1800 60 F/S REC SettingREC Quality Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP NET Enable OFF NET Setting SET Main SET RS232 Comm SettingCommunication RS232 Backup Full Disk REFORMAT/CLEAR Disk Setting Flicker Reduction System HD3 Situation Status Ntsc PAL SpecificationsJpeg General Command Format SetupCommunication Protocol Command Types Keys and signalsCommand Main Category=0x02 Handshake Second Category=0x01 Request Time Second Category=0x02 Set Time Second Category=0x02 Set Setup Values Second Category=0x04Request State Second Category=0x05 Description of System State Appendix 2. -- System Default Slave Backup Complete Battery LOWNo Entry for Backup Backup Incomplete Apendix 4. -- Network Viewing Connecting KV-HD01 to your networkSystem Requirements KV-HD01A RJ-45 PIN configuration for Ethernet Install the browsing software to your PCPhysical specification for Ethernet Open Network Viewer Picture B Picture a Viewing Image System status indicatorsPlay List PgUp & PgUp Changing Record Properties Changing The Record & Timer propertiesRate Quality Archive Images to the computer Change the Timer propertiesNumber of Saving Save Abort Exit Open the Image Viewer Quit Viewing a still JPEG-imagePrint Stop Digital Video Recorder