Toshiba RD-XV48DTKF Installing Batteries in the Remote Control, About the Remote Control, 14 EN

E3NG0FD_EN.book Page 14 Wednesday, January 30, 2008 10:37 AM

27VARIABLE SKIP button (HDD/DVD)

•Skips by the amount of time set in advance.

28DISC MENU button (HDD/DVD)

•Press to display the Disc menu during playback.

•Press to change the Original and Playlist on the TV screen.

29ENTER button

•Press to acknowledge or approve a menu selection.

•While watching a DVB channel, press to display the “Quick select” menu.

30RETURN button

•Press to return to the previously displayed menu screen.

31FWD D button

•When playback is paused, press to forward slowly.

(HDD/DVD)

•During playback, press to fast forward.

(VHS)

•Press to advance the videotape rapidly.

•Press to view the picture rapidly in forward during playback.

32STOP C button

•Press to stop playing back or recording.

33SKIP G button (HDD/DVD)

•During playback, press to skip to the next chapter or track.

•When playback is paused, press to advance step by step.

34HDD button

•Press to select the HDD output mode.

35DVD button

•Press to select the DVD output mode.

36REC I button

•Press once to start a recording.

•Press repeatedly to start a One-touch Timer Recording.

37REC MODE button

•Press to switch the recording mode.

38SAT.LINK button (HDD)

•Press to activate the Satellite Link Timer Recording.

39AUDIO D button

•For analogue channels when receiving a bilingual broadcast, press to change the audio out setting to “Main”, “Sub” or “Main/Sub”.

•Press to change the bilingual audio source of an external equipment to “Main”, “Sub” or “Main/Sub”. (Available only when the “External Input Audio” in “Setup” menu is set to “Bilingual” in advance.)

•Press to select the sound mode for DVB channels.

(HDD/DVD)

•Press to display the audio menu during playback.

(VHS)

•During playback of Hi-Fi videotape, press to change the audio out setting to “STEREO”, “LEFT”, “RIGHT” and “MONO”.

Button names described in the Owner’s Manual The instructions in this manual are described mainly with the operations using the remote control. Some operations can be carried out using the buttons on the front panel.

Note

•If you turn off this unit, [OPEN\CLOSE A] on the remote control is not available. Be sure to use [AOPEN\CLOSE] or [A / C EJECT/STOP] on the unit.

14 EN

Installing Batteries in the Remote Control

Install two R6 (AA) batteries (supplied) into the remote control, carefully match with the polarity indicated inside the battery compartment.

1 2 3

Caution

•Incorrect use of batteries can result in hazards such as leakage and bursting.

•Do not mix new and old batteries together.

•Do not use different kinds of batteries together.

•Make sure that the plus (+) and minus (–) ends of each battery match the indications inside the battery compartment.

•Remove batteries if the equipment will not be used for a month or more.

•When disposing used batteries, please comply with governmental regulations or the public instructions for environmental protection that apply in your country or area.

•Do not recharge, short-circuit, heat, burn or disassemble batteries.

About the Remote Control

•Make sure there is no obstacle between the remote control and the remote control sensor on the unit.

•Use within the operating range and angle as shown.

VCR	PROGRAM			SELECT		HDD/DVD
REC	DUBBING		VCR	HDD	DVD	REC
	VCR	DVD				HDD DVD
	HDD	DVD

7 m (30°) 7 m 7 m (30°) Within about 7 m

Remote control

• The maximum operable range as follows:

Line of sight: approximately 7 m

Either side of centre: approximately 7 m within

30degrees

•Remote control operation may become unreliable if the remote control sensor of the unit is being exposed by the strong sunlight or fluorescent light.

•Remote controls for different devices can interfere with each other. Be careful when using remote controls for other equipment located close to the unit.

•Replace the batteries when the operating range of the remote control reduces.