Toshiba RD-XV48DTKF Manual Tuning Analog, 26 EN, Channel Plan CH Indication TV Channel

Press [SETUP] to exit.

6

This unit can receive the Hyper and Oscar frequency bands.

• If “Skip” is set to “ON”, select “Skip” using [U \ D], then press [P]. Select “OFF” using

[U \ D], then press [L].

• If you want to decode scrambled signals, select “Decoder” using [U \ D], then press [P]. Select “ON” using [U \ D], then press [L].

• To store another channel, repeat steps 5 to 10.

11 Press [SETUP] to exit.

Skip a Preset Channel

ANALOG

You can set the unit to skip channels. You can no longer receive or watch when you access channels using [PROG. G \ H].

1 Follow steps 1 to 4 in “Manual Tuning (ANALOG)” on this page.

2 Select “Position” using [U \ D], then press [P].

3 Select the position number you want to skip using [the Number buttons] or [U \ D], then press [L].

4 Select “Skip” using [U \ D], then press [P].

5 Select “ON” using [U \ D], then press [L].

• To skip another channel, repeat steps 2 to 5.

E3NG0FD_EN.book Page 26 Wednesday, January 30, 2008 10:37 AM

Manual Tuning (ANALOG)

ANALOG

You can preset an analogue channel manually and individually.

1 In stop mode, press [SETUP]. Select “General Setting” using [U \ D], then press [ENTER].

2 Select “Channel” using [U \ D], then press [ENTER].

3 Select “ANALOG Channel Setup” using [U \ D], then press [ENTER].

4 Select “Manual Tuning” using [U \ D], then press [ENTER].

5 Select “Position” using [U \ D], then press [P].

Manual Tuning

Position	901
System	L
Channel	1
Decoder	OFF
Skip	ON

6 Select the position number you want to use using [the Number buttons] or [U \ D], then press [L].

•You can select position number 901-999.

•With [the Number buttons], you only need to enter the last 2-digit numbers.

7 Select “System” using [U \ D], then press [P].

8 Select “L” or “BG” using [U \ D], then press [L].

•If your system is SECAM-L,select “L”.

•If your system is PAL-B/G,select “BG”.

9 Select “Channel” using [U \ D], then press [P].

10 Press [U \ D] to start scanning.

•The tuner will begin to search up or down automatically. When a channel is found, the unit will stop searching and the picture will appear on the TV screen.

•You can select a desired channel number using [the Number buttons]. Refer to the following Channel Plan table and press the three digits to select the channel number.

(To select channel 4, press [0] first and then press [0] and [4]. Or press [4] and then “– – 4” appears and wait for 2 seconds.)

•If this is the channel you want, press [L].

[L (SECAM-L)]

Channel Plan

CH Indication		TV Channel
01	– 10	F1 - F10
21	– 69	E21 – E69
74	– 86	B – Q
90 – 106		S4 – S20
121	– 141	S21 – S41
[BG (PAL-B/G)]
	Channel Plan
CH Indication		TV Channel
02	– 12	E2 - E12
13	– 20	A – H (only ITALY)
21	– 69	E21 – E69
74	– 78	X, Y, Z, Z+1, Z+2
80 – 99, 100		S1 – S20, GAP
121	– 141	S21 – S41

26 EN