Toshiba RD-XV48DTKF

Time Search

This feature allows you to go to a specific point on a

tape by entering the exact amount of time you want to

skip in order to reach the point.

1Press [VCR].

2Press [SEARCH] repeatedly until the

time search menu appears.

3Enter your desired time to skip using

[the Number buttons] within 30

seconds.

4Press [FWD D] or [REV E] to start

time search.

If you want to go in the forward direction, press

[FWDD].

If you want to go in the reverse direction, press

[REVE].

After index search, the unit will play back the tape

automatically.

Note

• This function is not available during recording.

•Press [STOPC] to stop the search.

• If the tape reaches the end during the search, this

unit will cancel it and rewind the tape.

• You can set the time up to 9:59.

Other Operations

Press [VCR] first.

To cue or review picture during playback

(PictureSearch):

Press [FWDD] or [REV E] during playback.

Press it again and the unit will search in super high

speed (in the LP mode only).

To freeze the picture on TV screen during

playback (Still mode):

Press [PAUSEF]. Each time you press the button,

the picture will be forwarded frame by frame.

If the picture begins to vibrate vertically during the still

mode, stabilise the picture by pressing the

[PROG.G\H]. If the picture is distorted or rolling

vertically, adjust the vertical hold control on your TV, if

equipped.

To reset the tape counter:

Press [CLEAR].

To play back in slow forward motion:

During playback, press [PAUSEF], then press

[FWDD].

If the noise bars appear on the TV screen, you can

reduce it by pressing [PROG.G\H]. Slow reverse

is not available in VHS mode.

Note

• Still / Slow / Pause mode will be automatically

cancelled after 5 minutes to prevent damage to the

tape and the video head.

• To return to normal play back from the Picture

Search / Still / Slow mode, press [PLAYB].

Changing the Video Colour

System

Different countries use different television colour

systems.

This unit will distinguish the video colour system

(SECAM, PAL or MESECAM) automatically according

to the format of a pre-recorded video tape during

playback or the input signal from the tuner or external

devices.

To change the video colour system manually, press

[MODE].

Each time you press [MODE], the colour system will

change as follows.

Note

• If the playback picture on the TV screen is black and

white, change the video colour system manually.

• When you change the video colour system

manually, be sure to change it before recording. If

you select the wrong video colour system for

recording, the colour of the picture may be

deteriorated.

Hi-Fi Stereo Sound System

This unit will record and playback Hi-Fi stereo sound.

In addition, it has an A2 and NICAM stereo sound

decoder. This unit will receive stereo and bilingual

broadcasts and it is possible to record in several ways

and to play back the sound.

Selecting the Sound Mode

You can select each mode by pressing [AUDIOD]

on the remote control. Each mode is indicated on the

TV screen as following.

• During playback of the recorded tape in Hi-Fi mode

• During reception of bilingual broadcasts

Note

• If you play back non-Hi-Fi tapes, the unit will play

back automatically in monaural even if you select

any mode.

• If the stereo signal becomes weak, the broadcast is

automatically recorded in monaural.

VHS

Mode Audio output Display on

the TV screen

Stereo Stereo STEREO

L L audio from both speakers LEFT

R R audio from both speakers RIGHT

Normal Monaural MONO

Mode Audio output Display on

the TV screen

Main Main audio from the both

speakers Main

Sub Sub audio from the both

speakers Sub

Main /

Sub

• Main audio from the left

speaker

• Sub audio from the right

speaker

Main

Sub

AUTO SECAM PAL MESECAM

Introduction Connections Basic Setup Playback Editing OthersFunction SetupRecording VHS Functions

E3NG0FD_EN.book Page 95 Wednesday, January 30, 2008 10:37 AM