System Assembly | Trilogy Touch Technology 9 manual

Commander Installation Guide

2.4SYSTEM ASSEMBLY

If the system is multi-frame (i.e. > 96 ports), it will be supplied with frame 1 at the bottom and frames 2,3,4 etc. ascending from there. Some earlier systems were supplied with the frames configured in descending order.

The system modules will normally be packed separately for transit. Carefully remove all of the packing materials taking care to leave the modules in their anti-static protection for as long as possible.

Module variants are indicated by the type suffix, e.g. 500-06-00. In general, there is complete backward compatibility between all versions of the modules. Modules supplied as part of a complete system are compatible and will have been system checked accordingly.

Identify the modules and fit them into the frame in the following order:

1.500-08 Changeover Module. See section 2.4.1.

2.500-02 Talkback Controller (main controller only) See section 2.4.2.

NOTE: Items 1 and 2 may be supplied pre-assembled. Check carefully!

3.500-01 TDM Controller (main controller only). See section 2.4.3.

4.Optional 500-10 Misc. I/O (GPI) Modules. See section 2.4.5.

5.Optional 500-25 Network Cards. See section 2.4.4.

6.500-06 Matrix Cards. See section 2.4.6.

The diagram below shows the correct location within each frame.

Please note the positions of the modules. Incorrect location of modules will

result in damage to the electronics.

If in doubt, contact Trilogy BEFORE switching on the power.

Standby Talkback Controller

Standby TDM Controller

Matrix Cards 3 - 15

Changeover Module

Matrix Cards

Main TDM Controller

Main Talkback Controller

Page 10 of 81

Issue 9

Trilogy Communications Limited

Image 10

Trilogy Touch Technology 9 manual System Assembly

Contents

Installation Guide Document Number Issue Date Reason for Change Approved50096601.doc Errata Sheet Description Contents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Unpacking IntroductionRack Mounting System Assembly 500-08-10 Changeover Module 1 500-08 Series Changeover Card Commander Installation Guide Commander Installation Guide 4 500-25-00 E1 Network Link Card 5 500-10 Series MISC. I/O GPI Cards 6 500-06 Series Matrix Cards D9 Fixed Plug Pin Function Mains Connection and Fusing1 500-15-30 Series Power Supply XLR4 Fixed Socket Pin Function Starting the System Commander Installation Guide Connecting the PC to the Commander System Connecting the Matrix PortsConnection VIA a PC COM Port Using RS232 Sub D 9 free female Sub D 9 free male Connection VIA a 500-16-03 Download Converter BOXSub D 9 free female Installing Pathfinder 574 not 576 for a six frame system Other Matrix Connections Camera ConnectorMatrix Ports RJ-45 Alarms RS232 configurationRS422 configuration Serial Link RS232 / RS422 Miscellaneous I/O Card Connector PIN-OUT Commander D37 Fixed Plug Pin Description Commander D25 Fixed Socket Lower Connector Pins Description Commander D25 Fixed Socket Upper Connector Pins DescriptionCommander D9 Fixed Socket Pin Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output 5.3 500-25 Network Card Indicators and Switches LED Configuring the Gain of Camera Inputs .5.1 Link Setting on Connecting Networked Systems 1 500-26 Network Rear Connector Unit RCU Either Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification RJ-45 Function Pin 2 500-3X-5X Series Standard Control Panel Rear ViewExpansion Port RJ45 socket Matrix and Expansion RJ45 socket view from rear of panel Keypad D9 Fixed Socket -51 variant only Gpio Local logic in and out D9 Fixed SocketAudio I/O D15 Fixed Socket View of Keypad front panel 4 500-3X-5X Series DIP Switch Settings OFF Rear Connector Layout Expansion out RJ-45 fixed socket on panel Rear Connecor Layout ConnectionsMatrix RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket View of Keypad as seen on front panel Keypad D9 Fixed SocketControl Panel Gpio External Circuitry Rear Panel Layout Connector types500-31-60 Standard Facility 16 KEY Control Panel Headset 5 Pin XLR Fixed Socket front panel Gpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme 4.2 500-02-1x Talkback Controller Connecting the Hardware4.3 500-3x-3x Control Panels 4.4 500-08-10 Changeover Card Commander Programming Cable Way D Male Way D FemaleProgramming with the 500-16-03 Download Converter Beltpacks RM15TPD-12S Telephone Interfaces Connector Detail per channelConnector Detail Trilogy 500-19-10 Telephone Interface Frame Telos ONE Alignment RT Equipment 500-22-00 ICIS-1 Isdn Interface Remote Ports Isdn Interface RJ45 ConnectorCom Port 1.5 RJ45 500-23-00 ICIS-2 Isdn Interface D15 Fixed Plug on ICIS-2 DTE Gain Setting on Matrix Cards Matrix Download Power SuppliesComputer Operating Systems Important Note Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panels Legacy Control Panel Facility Comparison Table 2.1 500-3x-3x Series Standard Control Panel Rear View Test Port- D9 Fixed Socket Expansion Port- D9 Fixed Socket 3 500-30 Series DIP Switch Settings 4 500-40-0X Series Expansion Panels Connector Pin Out Expansion In D9 Fixed SocketExpansion Out- D9 Fixed Socket Commander Installation Guide Page Type B max length 10 metres D9 Free Plug Function Pin Connecting VIA Structured CablingD9 pin RJ 45 pin Colour see above 6.1 500-39-30 Connector Pin Out 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker 7 500-3X-5X Series Control Panels 6.2 500-39-30 Rear View8 500-43-51 1U, 8 REN Level Control Panel Real Time Performance Matrix Audio Specification Using 500-06-02 Matrix CardsGeneral Panels Miscellaneous I/O Card P.C 10.2 500-41 Desktop Panel Internal Settings 10.1 500-3X-5X Series Internal Panel Switch SettingsCut Switch Action No action HSMic LSCut MCCut Off 10.3 500-31-60 Programming CUT Switch OperationTest Function Loop Back Test Mode Safety PrecautionsMains Connector and Plug Transportation and Storage