Installing Pathfinder | Trilogy Touch Technology 9 instruction

Commander Installation Guide

3.3INSTALLING PATHFINDER

PathFinder is the configuration editor for the Trilogy Commander intercom system. Details of PC specification and operating system requirements are given in Section 9.6. Software is supplied on CD-ROM. For a new installation, insert the disk in the PC CD drive.

From the Windows start menu, click Run, then type x:PathFinder 4_nn\Disk1\setup.exe where x is the CD drive letter and nn is the version sub-code (e.g. 21).

Alternatively, browse to the location using Windows Explorer.

Unless there are exceptional reasons otherwise, we strongly recommend that you accept all the defaults offered during the software installation process. Following this, you will be prompted that a system re-start is required, which again should be followed to provide correct operation.

There are now some important settings to carry out before using PathFinder.

•System name and number

•The matrix size.

•Commander interface method and settings.

Start PathFinder, entering the CD key code when prompted. This is attached to the CD jewel case and should be carefully retained for future PC installations. Follow the options to create a New Database. From the Options pull down menu, select Settings and the form shown below will be displayed.

Trilogy Communications Limited

Issue 9

Page 21 of 81

Image 21

Trilogy Touch Technology 9 manual Installing Pathfinder

Contents

Installation Guide Issue Date Reason for Change Approved Document Number50096601.doc Description Errata Sheet Contents Introduction Control Panels Legacy Hardware Options Available and Module Type Numbers Commander Installation Guide Issue Introduction UnpackingRack Mounting System Assembly 1 500-08 Series Changeover Card 500-08-10 Changeover Module Commander Installation Guide Commander Installation Guide 5 500-10 Series MISC. I/O GPI Cards 4 500-25-00 E1 Network Link Card 6 500-06 Series Matrix Cards 1 500-15-30 Series Power Supply Mains Connection and FusingD9 Fixed Plug Pin Function XLR4 Fixed Socket Pin Function Starting the System Commander Installation Guide Connecting the Matrix Ports Connecting the PC to the Commander SystemConnection VIA a PC COM Port Using RS232 Connection VIA a 500-16-03 Download Converter BOX Sub D 9 free female Sub D 9 free maleSub D 9 free female Installing Pathfinder 574 not 576 for a six frame system Camera Connector Other Matrix ConnectionsMatrix Ports RJ-45 RS422 configuration RS232 configurationAlarms Serial Link RS232 / RS422 Commander D37 Fixed Plug Pin Description Miscellaneous I/O Card Connector PIN-OUT Commander D25 Fixed Socket Upper Connector Pins Description Commander D25 Fixed Socket Lower Connector Pins DescriptionCommander D9 Fixed Socket Pin Description 5.1 500-10 Switches and Indicators Suggested external wiring of Misc I/O card output LED 5.3 500-25 Network Card Indicators and Switches Configuring the Gain of Camera Inputs .5.1 Link Setting on 1 500-26 Network Rear Connector Unit RCU Connecting Networked Systems Either Serial Networking Commander Installation Guide Issue Current Range Control Panel Facility Comparison Table 500-41-XX Series Desktop Panels Specification Expansion Port RJ45 socket 2 500-3X-5X Series Standard Control Panel Rear ViewRJ-45 Function Pin Matrix and Expansion RJ45 socket view from rear of panel Audio I/O D15 Fixed Socket Gpio Local logic in and out D9 Fixed SocketKeypad D9 Fixed Socket -51 variant only View of Keypad front panel OFF 4 500-3X-5X Series DIP Switch Settings Rear Connector Layout Rear Connecor Layout Connections Expansion out RJ-45 fixed socket on panelMatrix RJ-45 fixed socket on panel Gpio Local logic in and out D9 Fixed Socket Keypad D9 Fixed Socket View of Keypad as seen on front panelControl Panel Gpio External Circuitry 500-31-60 Standard Facility 16 KEY Control Panel Connector typesRear Panel Layout Headset 5 Pin XLR Fixed Socket front panel Gpio Local logic in and out D9 Fixed Socket 10 500-33-00 / 500-45-00 / 500-46-00 Range Gpio Local logic in and out D9 Fixed Socket Commander Installation Guide Issue Ttprog Software 6.2.1 SET-UP Routine Starting the Programme Connecting the Hardware 4.2 500-02-1x Talkback Controller4.3 500-3x-3x Control Panels Commander Programming Cable Way D Male Way D Female 4.4 500-08-10 Changeover CardProgramming with the 500-16-03 Download Converter RM15TPD-12S Beltpacks Connector Detail Connector Detail per channelTelephone Interfaces Trilogy 500-19-10 Telephone Interface Frame Telos ONE Alignment 500-22-00 ICIS-1 Isdn Interface RT Equipment Com Port Isdn Interface RJ45 ConnectorRemote Ports 1.5 RJ45 D15 Fixed Plug on ICIS-2 DTE 500-23-00 ICIS-2 Isdn Interface Matrix Cards Gain Setting on Power Supplies Matrix DownloadComputer Operating Systems Important Note Installing AN Archipel Download Card in a P.C Commander Installation Guide Black BOX IC114A Pcmcia Serial Adaptor Card Matrix Ports D9 Legacy Control Panel Facility Comparison Table Legacy Control Panels 2.1 500-3x-3x Series Standard Control Panel Rear View Expansion Port- D9 Fixed Socket Test Port- D9 Fixed Socket 3 500-30 Series DIP Switch Settings Connector Pin Out Expansion In D9 Fixed Socket 4 500-40-0X Series Expansion PanelsExpansion Out- D9 Fixed Socket Commander Installation Guide Page Connecting VIA Structured Cabling Type B max length 10 metres D9 Free Plug Function PinD9 pin RJ 45 pin Colour see above 6 500-39-30 / 31 1U 12 KEY Panel with Loudspeaker 6.1 500-39-30 Connector Pin Out 6.2 500-39-30 Rear View 7 500-3X-5X Series Control Panels8 500-43-51 1U, 8 REN Level Control Panel General Matrix Audio Specification Using 500-06-02 Matrix CardsReal Time Performance Panels P.C Miscellaneous I/O Card 10.1 500-3X-5X Series Internal Panel Switch Settings 10.2 500-41 Desktop Panel Internal SettingsCut Switch Action No action 10.3 500-31-60 Programming CUT Switch Operation HSMic LSCut MCCut OffTest Function Mains Connector and Plug Safety PrecautionsLoop Back Test Mode Transportation and Storage