iiI N T R O D U C T I O N

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

(a)DO NOT operate or allow the oven to be operated with the door open.

(b)Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing,

(3)seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.

(c)Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.

(d)Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.

(e)A microwave leakage check to verify compliance with the Federal performance standard should be performed on each oven prior to release to the owner.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This oven is equipped with a cord that has a grounding wire with a grounding plug, which must be plugged into an outlet that is properly installed and grounded. Consult a qualified electrician or serviceman if uncertain about the ability to follow ground- ing instructions or if doubt exists as to whether the appliance is properly grounded.

†x D O N O T use an extension cord. If the power cord is too short, have a qualified electrician or service- man install an outlet near the appliance.

W A R N I N G : Improper grounding can result in risk of electric shock.

POWER CORD REPLACEMENT

If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly quali- fied person.

RF INTERFERENCE CONSIDERATIONS

The NGC (Tornado) oven generates radio frequency signals. This device has been tested and was determined to be in compliance with applicable portions of FCC part 18 requirements and to the protection require- ments of Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility at the time of manufacture. However, some equipment with sensitivity to signals below these limits may experience interference.

If your equipment experiences interference:

†Increase the physical separation between this oven and the sensitive equipment.

†If the sensitive device can be grounded, do so following accepted grounding practices.

†If battery-powered microphones are being affected, ensure that the batteries are fully charged.

†Keep sensitive equipment on separate electrical circuits if possible.

†Route intercom wires, microphone wires, speaker cables, etc. away from the oven.

Page 7 Page 9
Page 8
Image 8
Turbo Chef Technologies NGC-1007 service manual Grounding Instructions
Page 7 Page 9

NGC-1007 specifications

TurboChef Technologies has made a substantial impact in the commercial cooking industry with its advanced cooking equipment, and one of their standout products is the NGC-1007. The NGC-1007 is a revolutionary cooking oven designed to meet the demands of high-paced kitchens while ensuring superior cooking quality and efficiency.

One of the main features of the NGC-1007 is its high-speed cooking technology. Utilizing a combination of convection, impingement, and microwave cooking, this oven can reduce cooking times significantly while maintaining food quality. This multi-cooking method not only speeds up the cooking process but also enhances flavor and texture, making it ideal for cooking a wide variety of dishes, from pizzas to entrees.

The NGC-1007 also showcases advanced control technology, incorporating a user-friendly touch screen interface. This intuitive control panel allows chefs to easily navigate through various cooking settings and recipes, ensuring that each dish can be prepared to perfection. With programmable settings, operators can store favorite recipes and recall them at the touch of a button, improving efficiency and consistency in food preparation.

The design of the NGC-1007 reflects a commitment to reliability and durability. Built with high-quality materials, it can withstand the rigors of a bustling kitchen environment. Its compact size is perfect for establishments with limited space yet powerful enough to handle the demands of high-volume cooking.

Another key characteristic of the NGC-1007 is its energy efficiency. TurboChef has integrated innovative technology that reduces energy consumption without compromising cooking performance. This not only helps in cutting operational costs for restaurants but also aligns with sustainability goals by minimizing the environmental impact.

Furthermore, the NGC-1007 is equipped with easy-to-clean surfaces, making maintenance hassle-free. This is crucial in any busy kitchen, as it allows staff to focus on food preparation and service rather than extensive cleanup.

In summary, the TurboChef NGC-1007 is a game-changer for commercial kitchens looking to optimize their cooking processes. With its high-speed cooking capabilities, intuitive controls, durable construction, energy efficiency, and ease of maintenance, it stands out as a reliable option for chefs aiming to elevate their culinary output while managing time and resources effectively.
Top Page Image Contents