Set-up | Ultra electronic Prima 2e instruction

Set-up

Connecting the IC unit

(sold separately)

Large and compact size IC units are sold separately, as are specialized optional devices for the printer. Consult your dealer for more details.

WARNING

•Make sure that the power switch is turned OFF and the AC cable is detatched from the plug, before connecting and disconnecting the IC units. Otherwise

Electric

shock electric shocks, fires or malfunction of the product may occur.

•Using IC units other than those specified may cause electric shocks, fires or malfunction of the product.

Large size IC unit (sold separately)

1. A joint plate for an IC unit is provided as an accessory.

2. Fit the printer and IC unit into the holes as shown.

CX21ICL*

CX21ICL* is manufactured by us.

CAUTION

Unstable locations and angled surfaces may cause card feeder malfunctions. Make sure

to fit the devices into the holes securely.

Furthermore, install the printer on a flat and hard surface.

3. Connect the printer and IC unit.

Connect the cable which comes with the IC unit to the

OPTION 1 terminal.

Connecting to the PRT interface terminal

Connection cable (Accessory)

Use the OPTION 1 side.

If you use side 2 it does not function.

CAUTION

Turn the power off before connecting the cable between the printer and IC Unit. Otherwise some malfunction may be caused.

4. Connect the IC unit with the host computer.

Connect interface cables which are commercially available.

The terminal is rotated 180

°

Commercial item
Terminals on the rear of the IC unit	SERIAL1:non-contact
	SERIAL2:contact

CAUTION

Make sure to tighten the screws of the interface cables.

11

Image 11

Ultra electronic Prima 2e instruction manual Set-up, Connecting the IC unit Sold separately

Contents

See p.42~43 See p.11~13,22See p.23~35 See p.19~21 Declaration of Conformity Machine noise Operation is subject to the following two conditions Contents Do not wet the machine with water Do not touch the power plug during electrical stormsManual any time as you need Do not use a line voltage other than instructed Do not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning the machine Hold the body of the power plug when pulling it out Handling of transfer film Ink ribbons and cards Product featuresChecking accessories Before use Escape Clause Do not place objects on top InstallationInstallation diagram 35% to 70% Names of parts Make sure to tighten the screws of the interface cables Connecting the IC unit Sold separatelySet-up Malfunction of the product Connecting the LaminatorInstall the unit connecting cable.optional Product may occur North America Europe Connecting the power cordCheck the plug For AC 120V type Side Installing the card stackerHang the stacker claw on the stacker receptacle Card stacker is capable of containing approximately Do not touch the surface of the ink ribbon with your hands Setting the ink ribbonRemove the ink ribbon cassette Place the cassette upright on a flat surface during set-up Appears on the LCD panel When the ink ribbon is wound up to the endClose the printer door Insert the cassette along the guide rail Otherwise the printer may fail Slowly Setting the retransfer filmActivate the slide knob and open the printer door Insert the retransfer film into the cassette If the retransfer film is not set properly When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassette Inserting cards Setting cardsCassette and/or the ink ribbon cassette Shown in the illustration Consult your dealer to purchase new gloves When moving the card bracket For ISO cards When using magnetic cardsSwitching the card thickness For JIS II cards Connect the printer and host computer with the USB cable Connecting with a host computerConnecting Multiple Printers When connecting a host computer to multiple printers Names of parts on the operation panel Beforeuse LCD panel Operation display LED contentsLCD operation display content Operation display LED Ready LED will light up Turning on the powerDo not turn the power off while Operation Is loaded Turning off the power User modes User mode screen flow Main menu Press To save Displayed when the power is turned onCounter select mode Color settings Clearing the free counter Cleaning modeSee p.38,39 and p.40 for executing the cleaning mode Press to reset Ink mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Unit No Setting Coercivity setting mode Test printNon-contact IC antenna setting mode IC contact setting mode Close the card tray CareandcleaningCleaning the cleaning rollers Open the card tray Remove the cleaning unit Wipe the head indicated with Cleaning the thermal headCleaning the fan filter See p.15, 17 in this manual See p.30 in this manual Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions If the sponge is removed, attach it again as shown below Confirm that the retransfer film cassette has been removed Cleaning the magnetic headSet a cleaning card More Periodical Maintenance Cleaning of the bobbin holdersOnce printer servicing and cleaning Have been completed Feed roller TroubleshootingAll rollers require routine cleaning Layout of rollers inside the printer To initialize the unit Error code listing MG mechanical error Hardware errorError MG connection error Mending broken ink ribbon Retransfer film Stopping when printingAbout printing errors When retransfer operation is not complete Hopper jam Pull out the card tray Removing card jams Injury Retransfer section Jam transfer Specifications 343 381 External appearance and dimensionsFront view Side view Unit/mm Software License Agreement Page End of Agreement USA