Usa | Ultra electronic Prima 2e specification

Ultra Electronics Card Systems Inc.		Ultra Electronics Card Systems
North American Sales & Support Center		Waverley House
6711 - 176th Avenue NE		Hampshire Road
Redmond, WA 98052		Granby Estate
	USA	Weymouth, DT4 9XD
Tel: (425)	556 9708	UK
Fax: (425)	556 3962	Tel: +44 (0) 1305 784 738
Email: sales@UltraMagicard.com		Fax: +44 (0) 1305 777 904
		Email: UKsales@UltraMagicard.com

Page 52

Image 52

Ultra electronic Prima 2e instruction manual Usa

Contents

See p.11~13,22 See p.23~35See p.19~21 See p.42~43 Declaration of Conformity Operation is subject to the following two conditions Machine noise Contents Do not touch the power plug during electrical storms Manual any time as you needDo not use a line voltage other than instructed Do not wet the machine with water Do not use the machine while it has a fault Pull out the power plug before cleaning the machineHold the body of the power plug when pulling it out Do not touch the power plug with a wet hand Product features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cards Escape Clause Installation Installation diagram35% to 70% Do not place objects on top Names of parts Set-up Connecting the IC unit Sold separatelyMake sure to tighten the screws of the interface cables Connecting the Laminator Install the unit connecting cable.optionalProduct may occur Malfunction of the product Check the plug For AC 120V type Connecting the power cordNorth America Europe Installing the card stacker Hang the stacker claw on the stacker receptacleCard stacker is capable of containing approximately Side Setting the ink ribbon Remove the ink ribbon cassettePlace the cassette upright on a flat surface during set-up Do not touch the surface of the ink ribbon with your hands When the ink ribbon is wound up to the end Close the printer doorInsert the cassette along the guide rail Appears on the LCD panel Setting the retransfer film Activate the slide knob and open the printer doorInsert the retransfer film into the cassette Otherwise the printer may fail Slowly When the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the printer door and insert the cassette If the retransfer film is not set properly Setting cards Cassette and/or the ink ribbon cassetteShown in the illustration Inserting cards When moving the card bracket Consult your dealer to purchase new gloves When using magnetic cards Switching the card thicknessFor JIS II cards For ISO cards Connecting with a host computer Connecting Multiple PrintersWhen connecting a host computer to multiple printers Connect the printer and host computer with the USB cable Beforeuse Names of parts on the operation panel LCD operation display content Operation display LED contentsLCD panel Turning on the power Do not turn the power off whileOperation Operation display LED Ready LED will light up Turning off the power Is loaded User mode screen flow User modes Main menu Displayed when the power is turned on Counter select modeColor settings Press To save Cleaning mode See p.38,39 and p.40 for executing the cleaning modePress to reset Clearing the free counter Ink mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Coercivity setting mode Test print Non-contact IC antenna setting modeIC contact setting mode Unit No Setting Careandcleaning Cleaning the cleaning rollersOpen the card tray Remove the cleaning unit Close the card tray Cleaning the thermal head Cleaning the fan filterSee p.15, 17 in this manual Wipe the head indicated with Cleaning the card feed rollers and heat Rollers Install the fan filters back to the original positionsIf the sponge is removed, attach it again as shown below See p.30 in this manual Cleaning the magnetic head Set a cleaning cardMore Confirm that the retransfer film cassette has been removed Once printer servicing and cleaning Have been completed Cleaning of the bobbin holdersPeriodical Maintenance Troubleshooting All rollers require routine cleaningLayout of rollers inside the printer Feed roller Error code listing To initialize the unit Hardware error ErrorMG connection error MG mechanical error Stopping when printing About printing errorsWhen retransfer operation is not complete Mending broken ink ribbon Retransfer film Removing card jams Hopper jam Pull out the card tray Injury Retransfer section Jam transfer Specifications External appearance and dimensions Front viewSide view Unit/mm 343 381 Software License Agreement Page End of Agreement USA