Manuals / Ultra electronic / Computer Equipment / Printer

Ultra electronic Prima 2e Connecting the Laminator, Product may occur, Malfunction of the product

Models: Prima 2e

1 52

Download 52 pages 38.52 Kb

Page 12

Set-up(continued)

Compact IC unit (sold separately)

Please ask your dealer for the Compact IC unit connection.

Connect the compact IC unit to the host computer with the interface cables which are commercially available.

CAUTION

Be careful not to pinch your finger when installing.

2. install the laminator

Compact IC unit	Laminator(ILU)

Interface cable	Memo
(Commercial item)

Connecting the Laminator

The laminator is sold separately, as a specialized optional device for the printer. Consult your dealer for more details.

WARNING

•Make sure that the power switch is turned OFF and the AC cable is detatched from the plug, before connecting and

Electric	disconnecting the laminator. Otherwise
shock	electric shocks, fires or malfunction of the
	product may occur.
	• Using laminator other than those specified
	may cause electric shocks, fires or
	malfunction of the product.

If the mounting is uneven, the card would not be transported smoothly. be sure to fit the units right in. Always install the unit at a holizontal and hard surface location

3. Install the unit connecting cable.(optional)

As shown in the diagram, connect the cable to the OPTION 2 external connection terminal of the printer and the PRINTER external connection terminal of the laminator.

OPTION2

1. Set up the unit joint plate which comes with the laminator (optional). Mount the printeron to joint plate.

PRINTER

9 pin

9 pin

Connecting cable

XIDi

Printer

FRONT

FRONT

Tight the screw after connecting

CAUTION

Make sure to tighten the screws of the interface cables.

12

Joint Plate

Image 12

Ultra electronic Prima 2e instruction manual Connecting the Laminator, Product may occur, Malfunction of the product

Contents

See p.11~13,22 See p.23~35See p.19~21 See p.42~43Declaration of Conformity Operation is subject to the following two conditions Machine noiseContents Do not touch the power plug during electrical storms Manual any time as you needDo not use a line voltage other than instructed Do not wet the machine with waterDo not use the machine while it has a fault Pull out the power plug before cleaning the machineHold the body of the power plug when pulling it out Do not touch the power plug with a wet handProduct features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cardsEscape Clause Installation Installation diagram35% to 70% Do not place objects on topNames of parts Connecting the IC unit Sold separately Set-upMake sure to tighten the screws of the interface cables Connecting the Laminator Install the unit connecting cable.optionalProduct may occur Malfunction of the productConnecting the power cord Check the plug For AC 120V typeNorth America Europe Installing the card stacker Hang the stacker claw on the stacker receptacleCard stacker is capable of containing approximately SideSetting the ink ribbon Remove the ink ribbon cassettePlace the cassette upright on a flat surface during set-up Do not touch the surface of the ink ribbon with your handsWhen the ink ribbon is wound up to the end Close the printer doorInsert the cassette along the guide rail Appears on the LCD panelSetting the retransfer film Activate the slide knob and open the printer doorInsert the retransfer film into the cassette Otherwise the printer may fail SlowlyWhen the retransfer film is wound up to the end Wind the retransfer film to take up the slackOpen the printer door and insert the cassette If the retransfer film is not set properlySetting cards Cassette and/or the ink ribbon cassetteShown in the illustration Inserting cardsWhen moving the card bracket Consult your dealer to purchase new glovesWhen using magnetic cards Switching the card thicknessFor JIS II cards For ISO cardsConnecting with a host computer Connecting Multiple PrintersWhen connecting a host computer to multiple printers Connect the printer and host computer with the USB cableBeforeuse Names of parts on the operation panelOperation display LED contents LCD operation display contentLCD panel Turning on the power Do not turn the power off whileOperation Operation display LED Ready LED will light upTurning off the power Is loadedUser mode screen flow User modesMain menu Displayed when the power is turned on Counter select modeColor settings Press To saveCleaning mode See p.38,39 and p.40 for executing the cleaning modePress to reset Clearing the free counterInk mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Coercivity setting mode Test print Non-contact IC antenna setting modeIC contact setting mode Unit No SettingCareandcleaning Cleaning the cleaning rollersOpen the card tray Remove the cleaning unit Close the card trayCleaning the thermal head Cleaning the fan filterSee p.15, 17 in this manual Wipe the head indicated withCleaning the card feed rollers and heat Rollers Install the fan filters back to the original positionsIf the sponge is removed, attach it again as shown below See p.30 in this manualCleaning the magnetic head Set a cleaning cardMore Confirm that the retransfer film cassette has been removedCleaning of the bobbin holders Once printer servicing and cleaning Have been completedPeriodical Maintenance Troubleshooting All rollers require routine cleaningLayout of rollers inside the printer Feed rollerError code listing To initialize the unitHardware error ErrorMG connection error MG mechanical errorStopping when printing About printing errorsWhen retransfer operation is not complete Mending broken ink ribbon Retransfer filmRemoving card jams Hopper jam Pull out the card trayInjury Retransfer section Jam transfer Specifications External appearance and dimensions Front viewSide view Unit/mm 343 381Software License Agreement Page End of Agreement USA