Connecting the power cord

Set-up(continued)

1. Check the plug.

• For AC 120V type	• For AC220-240V type
(North America)	(Europe)

*The detached power cords vary according to model and country of purchase.

2. Plug the power cable into the printer.

Plug the power cable of the laminator if it is installed.

CAUTION

Always use a grounded power outlet. Never share the outlet with other electrical equipment.

Use an AVR (Automatic Voltage Regulator) if there is a possibility of voltage fluctuation. Use an uninterruptible power source rather than an AVR if there is the possibility of uninterruptible power source.

Page 13

Image 13

Ultra electronic Prima 2e Connecting the power cord, Check the plug For AC 120V type, North America Europe

Contents

See p.23~35 See p.11~13,22See p.19~21 See p.42~43 Declaration of Conformity Machine noise Operation is subject to the following two conditions Contents Manual any time as you need Do not touch the power plug during electrical stormsDo not use a line voltage other than instructed Do not wet the machine with water Pull out the power plug before cleaning the machine Do not use the machine while it has a faultHold the body of the power plug when pulling it out Do not touch the power plug with a wet hand Checking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cards Escape Clause Installation diagram Installation35% to 70% Do not place objects on top Names of parts Set-up Connecting the IC unit Sold separatelyMake sure to tighten the screws of the interface cables Install the unit connecting cable.optional Connecting the LaminatorProduct may occur Malfunction of the product Check the plug For AC 120V type Connecting the power cordNorth America Europe Hang the stacker claw on the stacker receptacle Installing the card stackerCard stacker is capable of containing approximately Side Remove the ink ribbon cassette Setting the ink ribbonPlace the cassette upright on a flat surface during set-up Do not touch the surface of the ink ribbon with your hands Close the printer door When the ink ribbon is wound up to the endInsert the cassette along the guide rail Appears on the LCD panel Activate the slide knob and open the printer door Setting the retransfer filmInsert the retransfer film into the cassette Otherwise the printer may fail Slowly Wind the retransfer film to take up the slack When the retransfer film is wound up to the endOpen the printer door and insert the cassette If the retransfer film is not set properly Cassette and/or the ink ribbon cassette Setting cardsShown in the illustration Inserting cards Consult your dealer to purchase new gloves When moving the card bracket Switching the card thickness When using magnetic cardsFor JIS II cards For ISO cards Connecting Multiple Printers Connecting with a host computerWhen connecting a host computer to multiple printers Connect the printer and host computer with the USB cable Names of parts on the operation panel Beforeuse LCD operation display content Operation display LED contentsLCD panel Do not turn the power off while Turning on the powerOperation Operation display LED Ready LED will light up Is loaded Turning off the power User modes User mode screen flow Main menu Counter select mode Displayed when the power is turned onColor settings Press To save See p.38,39 and p.40 for executing the cleaning mode Cleaning modePress to reset Clearing the free counter Ink mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Non-contact IC antenna setting mode Coercivity setting mode Test printIC contact setting mode Unit No Setting Cleaning the cleaning rollers CareandcleaningOpen the card tray Remove the cleaning unit Close the card tray Cleaning the fan filter Cleaning the thermal headSee p.15, 17 in this manual Wipe the head indicated with Install the fan filters back to the original positions Cleaning the card feed rollers and heat RollersIf the sponge is removed, attach it again as shown below See p.30 in this manual Set a cleaning card Cleaning the magnetic headMore Confirm that the retransfer film cassette has been removed Once printer servicing and cleaning Have been completed Cleaning of the bobbin holdersPeriodical Maintenance All rollers require routine cleaning TroubleshootingLayout of rollers inside the printer Feed roller To initialize the unit Error code listing Error Hardware errorMG connection error MG mechanical error About printing errors Stopping when printingWhen retransfer operation is not complete Mending broken ink ribbon Retransfer film Hopper jam Pull out the card tray Removing card jams Injury Retransfer section Jam transfer Specifications Front view External appearance and dimensionsSide view Unit/mm 343 381 Software License Agreement Page End of Agreement USA

Set-up(continued)

Connecting the power cord

1. Check the plug.

• For AC 120V type

(North America)

(Europe)