Beforeuse | Ultra electronic Prima 2e specs

Beforeuse

Names of parts on the operation panel

LCD panel

	READY	RESET	MENU
	ERROR	RESET	MENU
	ERROR
		EXIT	ENTER

Operation display LED

READY LED (green)

ON	: unit ready, printer in operation
Flashing : receiving image data
OFF	: unit stopped due to error, or unit being set,
	initialized or preheated.

ERROR LED (red)

ON : operation error

OFF : normal status

If an error occurs while the buzzer is set to ON, an alarm will sound. If this happens, the LCD background color will change to red.

Buzzar

Operation display LED

Setting buttons

RESET

MENU

ENTER

EXIT

Control buttons

Initializes the printer by the software when an error occurs or an error is cancelled.

The user mode setting is displayed when the unit is in the Ready or Preheating status. The button is also used when canceling the operation lock during errors.

Confirms the mode selected in the user mode setting.

The parameter setting for each mode can be adjusted during the user mode setting.

Make sure to press the button to save the settings.

Quits setting and returns to the upper level setting screen.

LCD panel

During normal operation

Upper line : operation status display

(For details concerning the operation display, see p. 24 of this manual.)

Lower line : counter display

(Toggles between total counter/head counter/ free counter and roller counter.)

If an error occurs Displays the error status.

(For details concerning the error display, see p. 42 - 43 of this manual.)

During user mode

Displays various setting modes.

(For details concerning settings, see p. 27 in this manual.)

Display background color

Bright green : OS booting up

Orange	: Card feeding
Red	: Error

The above background colors can be selected in user mode settings.

(For details concerning settings, see p. 29 in this manual.)

23

Image 23

Ultra electronic Prima 2e instruction manual Beforeuse, Names of parts on the operation panel

Contents

See p.42~43 See p.11~13,22See p.23~35 See p.19~21 Declaration of Conformity Machine noise Operation is subject to the following two conditions Contents Do not wet the machine with water Do not touch the power plug during electrical stormsManual any time as you need Do not use a line voltage other than instructed Do not touch the power plug with a wet hand Do not use the machine while it has a faultPull out the power plug before cleaning the machine Hold the body of the power plug when pulling it out Handling of transfer film Ink ribbons and cards Product featuresChecking accessories Before use Escape Clause Do not place objects on top InstallationInstallation diagram 35% to 70% Names of parts Make sure to tighten the screws of the interface cables Connecting the IC unit Sold separatelySet-up Malfunction of the product Connecting the LaminatorInstall the unit connecting cable.optional Product may occur North America Europe Connecting the power cordCheck the plug For AC 120V type Side Installing the card stackerHang the stacker claw on the stacker receptacle Card stacker is capable of containing approximately Do not touch the surface of the ink ribbon with your hands Setting the ink ribbonRemove the ink ribbon cassette Place the cassette upright on a flat surface during set-up Appears on the LCD panel When the ink ribbon is wound up to the endClose the printer door Insert the cassette along the guide rail Otherwise the printer may fail Slowly Setting the retransfer filmActivate the slide knob and open the printer door Insert the retransfer film into the cassette If the retransfer film is not set properly When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassette Inserting cards Setting cardsCassette and/or the ink ribbon cassette Shown in the illustration Consult your dealer to purchase new gloves When moving the card bracket For ISO cards When using magnetic cardsSwitching the card thickness For JIS II cards Connect the printer and host computer with the USB cable Connecting with a host computerConnecting Multiple Printers When connecting a host computer to multiple printers Names of parts on the operation panel Beforeuse LCD panel Operation display LED contentsLCD operation display content Operation display LED Ready LED will light up Turning on the powerDo not turn the power off while Operation Is loaded Turning off the power User modes User mode screen flow Main menu Press To save Displayed when the power is turned onCounter select mode Color settings Clearing the free counter Cleaning modeSee p.38,39 and p.40 for executing the cleaning mode Press to reset Ink mode setting Retransfer mode setting Buzzer mode setting Card Thickness setting mode Unit No Setting Coercivity setting mode Test printNon-contact IC antenna setting mode IC contact setting mode Close the card tray CareandcleaningCleaning the cleaning rollers Open the card tray Remove the cleaning unit Wipe the head indicated with Cleaning the thermal headCleaning the fan filter See p.15, 17 in this manual See p.30 in this manual Cleaning the card feed rollers and heat RollersInstall the fan filters back to the original positions If the sponge is removed, attach it again as shown below Confirm that the retransfer film cassette has been removed Cleaning the magnetic headSet a cleaning card More Periodical Maintenance Cleaning of the bobbin holdersOnce printer servicing and cleaning Have been completed Feed roller TroubleshootingAll rollers require routine cleaning Layout of rollers inside the printer To initialize the unit Error code listing MG mechanical error Hardware errorError MG connection error Mending broken ink ribbon Retransfer film Stopping when printingAbout printing errors When retransfer operation is not complete Hopper jam Pull out the card tray Removing card jams Injury Retransfer section Jam transfer Specifications 343 381 External appearance and dimensionsFront view Side view Unit/mm Software License Agreement Page End of Agreement USA