Ultra electronic Prima 2e instruction manual Retransfer mode setting

Operation (continued)

Retransfer mode setting

Change settings according to the retranfer film and card used.

> R e t r a n s f e r >	EXIT	Exit user
		mode.
ENTER			Set retransfer film		Set film type
> > M e d i a T y p e			Two types of frame settings (1000 or 750 frames per film)
			• Set to adjust the retransfer film specification.
	S t d ( 1 0 0 0 / r o l l ) : 0			to select the setting and press ENTER
EXIT		Press						to save.
	MENU			(The electronic beep sounds .The
				beep will not sound if the buzzer mode setting is set to off.)
			*After exiting the user mode, press			RESET	and then pressENTER
			to initialize.
				If initialization is not carried out, the film type setting will have no effect on
				the printer.
> > T e m p . L e v e l			Set the retransfer temperature.			6 gradations can be set
			(from –3 or +2, the larger the value the higher the temperature)
	0 ( S t a n d a r d )		•	Retransfer may be not performed well depending on the
				cards. Increase the temperature level step by step until the
				card can be printed clearly.
EXIT		Press		to select the setting value and press ENTER
	MENU	to save.		(The electronic beep sounds .The beep will
				not sound if the buzzer mode setting is set to off.)
				*After exiting the user mode, press		RESET	and then press ENTER
				to initialize.
				If initialization is not carried out, the temperature will have no effect on the
				the printer.
> > S p e e d ( F r o n t )			Set the retransfer speed:		13 gradations can be set
			(from –10 to +2, the larger the value the faster the speed)
		- 2
			•	Partial incompletions may occur depending on the cards
	MENU			during retransfer. The performance is increased as the
EXIT				value is lowered. Specify the value mainly onthe retransfer
				roller temperature setting and use the speed setting for
				fine adjustments.
		Press		to select the setting value and pressENTER				to save.
			(The electronic beep sounds .The beep will not sound if the buzzer
> > S p e e d ( B a c k )			mode setting is set to off.)			13 gradations can be set
			Set the reverse retransfer speed:
		- 2	(from –10 to +2, the higher the value the faster the speed.)
EXIT	MENU		• Double-sided printing results in a warp depending on
				the cards. Change the speed to correct it.

							Press		to select the setting value and press ENTER
							to save.
							(The electronic beep sounds .The beep will not sound if the buzzer
							mode setting is set to off.)
	> > M G P r i n t ( J I S )
							Set the way of the peeling off the retransfer film
				Off			2 settings[On and Off]
							Depending on the card used,peeling off the retransfer filmmay not be
	EXIT						complete.
			MENU				For the cards with JIS magnetic stripes,setting "On" is recommended.
					• When setting "On",printing time will be longer by about1,5s
					• No mprovement is expected for the cards with ISO magnetic stripes.
					Press				to select the setting value and press ENTER
					to save.
						(The electronic beep sounds .The beep will not sound if the buzzer
						mode setting is set to off.)			2 settings[Front Wait and Back Wait]
	> > S t a n	d	b y M o d e MENU				Standby selection :
							In case of both side printing with optional
EXIT			Front Wait				unit connected, select either one of the card sides for standby.
				Press				to select the setting value and press ENTER		to save.

	(The electronic beep sounds .The beep will not sound if the buzzer
32	mode setting is set to off.)