Function description

Besides fixed standard functions, there are selectable standard functions and optional functions.

Selectable standard functions can be selected by chang- ing over The CP Unit switches and by establishing station No. 200 programming. Optional functions can be made available by using external equipment or additional units.

1. Standard Functions

1-1. Available across the other exchange

1)Automatic Line Release

The calling Station is released from the speech path if dialing is not completed within 5 seconds. The calling station is also released from the speech path if no response is given within 10 seconds, when calling a station in the privacy mode.

2)Camp-on-Busy

When the called party is busy, the caller can camp-on the line. After the conversation is finished, he is auto- matically put through.

3)Press-to-Talk

One-way conversation is possible by pressing the Press-to-Talk bar when the ambient noise is high at one party's station.

4)Single Digit Dialing

Single digit calling of numbers up to 4 digits in length can be made by one-touch operation.

1-2. Available only within the same exchange

5)Remote response

The station called by continuous calling tone can be remotely answered by other stations.

2.Selectable Functions

2-1. Available across the other exchange

6)Privacy

When calls are unwanted, turn Privacy switch on and a brief privacy tone sounds when the station is called.

7)Camp-on-Privacy

When called in the privacy mode from another station, calls can be connected immediately after releasing the Privacy switch.

8)Handset Response in Continuously Called Stations Full duplex handset conversation is available by lifting the handset when the continuous calling tone is heard.

9)One-touch Response in Continuously Called Stations

Hands-free conversation is available by just touching

any key except when the continuous calling tone is heard.

10)Personal Number Call

Calls can be connected by using Personal Numbers, other than normal station numbers when Personal Numbers are registered into any designated station.

11)Highest Executive Priority

The preprogrammed caller can interrupt forcibly the called party in busy mode. In this event original conversation is cancelled.

Tie-line

12)Selection of Dial Operation

(1)Numbering Schedules of Tie-line System (Stan- dard)

The exchanges A, B and C permit the following standard station Numbering Schedules: (Hardwired station number)

Type of Exchange

A

B

C

With Personal Number

200~

470 ~

740~

(Standard)

455

725

995

(2)Selectable First Station Number of Each Exchange

The first station number of each exchange can be selected from any of the following numbers (Hard- wired station number):

The system with Personal Numbers can't use No. 100~199.

(3) Paging Response

Paging response may be made either by pressing the

"Zone No.", or [Simply pressing ].

(4)General Purpose Control

Dial digit numbers change the output numbers.

13)Programmable Station Numbering

The system has programmable station numbers up to No. 999 other than the normal hardwired station numbers.

14)Group Blocking (Restricted Dialing)

Stations can be blocked into groups which cannot call or page each other unless further programming is done.

15)Restricted Access

Stations with access to All-call Paging, Conference and General Purpose Control can be limited.

16)Selectable Calling Tone

(Calling Tone/Paging Pre-Announcement Tone)

The time duration of the Calling Tone can be set for "long" (Trill note tone) or "short" (Single note tone)

or none. Similarly, Paging Pre-Announcement Tone

may be set for "long" (2 sec.) or "short" (1 sec.) or

none.

17)Time-out of Conversation and Paging Call

A Calling Time Limitation can be set, in case paging and normal calls are to be kept short or where cancel- ling calls might be forgotten.

18)Automatic Access to Paging

Specific Substations may initiate a Paging Call or Paging Response or Personal Number Call, etc. by simply picking up a handset.

2-2. Available only within the same exchange

19)Master/Sub Relationship

Substations can call Master stations by one-touch operation. In the event of Handset Substation, a call can be made from Substation to its designated master station by simply picking up a handset.

20)Call Transfer

The called party can transfer the call to other selected station. Call Hold and Call Back are also possible.

– 63 –

Page 67
Image 67
Vizio EXES-6000 CP-64 Camp-on-Busy, Press-to-Talk, Single Digit Dialing, Camp-on-Privacy, Highest Executive Priority