Battery charging | VTech LS6245 guide

Getting started

Battery charging

Once you have installed the battery, the screen indicates the battery status (see the table below). If necessary, place the handset in the telephone base to charge the battery. For best performance, keep the handset in the telephone base when not in use. The battery is fully charged after 16 hours of continuous charging. See the table on page 77 for battery operating times.

If the screen is blank, you need to charge the handset without interruption for at least 10 minutes to give the handset enough charge to use the telephone for a short time. The handset beeps and shows Low battery. If you are on a call in low battery mode, the handset beeps every minute.

The following table summarizes the battery charge indicators and actions to take.

Battery indicators			Battery status	Action

The screen is blank.			Battery has no charge	Charge without interruption
			and the handset cannot	until the screen shows
			be used.	HANDSET X (at least 10
				minutes).
The screen shows			Battery has very little	Charge without interruption
Place in charger and			charge and the handset	until the screen shows
		flashes.	cannot be used.	HANDSET X (at least
				four minutes).

The screen shows			Battery has enough	Charge without interruption
Low battery,			charge to be used for a	until the screen shows
		flashes, and the	short time.	HANDSET X (at least
		flashes, and the	short time.	HANDSET X (at least
handset beeps.				30 minutes).
The screen shows			Battery is charged.	To keep the battery charged,
HANDSET X.				place it in the telephone base
				when not in use.

Image 9

VTech LS6245 user manual Battery charging

Contents

User’s manual Congratulations Table of contents Answering system operation..67 AppendixIndex Getting started Parts checklist Cleaning tips for your touch screen telephone InstallationImportant notes Avoid placing the telephone base too close to Telephone base installation Charge light Battery installation Battery charging VOL+ Handset layout Home Telephone base layout FLASH/X To enter the main menu Handset main menu Telephone base main menu Introducing Bluetooth Bluetooth Glossary of terms Important Information Bluetooth at a glance Setup cell Bluetooth setupTo pair and connect a cell phone Device connected to base, and 1 and/or 2 displays To pair and connect a headset Setup headset Rename a paired device Paired devices View information of a paired device Remove a paired device Active devices Review the active devices listConnect/disconnect an active device Add an active device Replace an active deviceTo replace an active device To add an active device Remove an active device View information of an active deviceChange PIN Settings Handset settingsLCD language To select a language Clear voicemail To manually turn off these indicators To change the setting Auto keylockKey tone Set date/time 800 Home area code Ringer volume To adjust the handset ringer volumeRingers To select a ringer tone Ringer tone Telephone base settings LCD Language Turn off indicator? 800 Ringer Volume Ringer tone Select Home Answering system setup Answering system settingsUsing the handset Answer ON/OFF To change the setting Using the telephone base Using a handsetCall screening Play your announcement Announcement Record your own announcement Tone. Press 5 when you are done. After the tone Delete your announcement Number of rings Press the Menu softkey when the handset is not in use Remote access code Message alert tone Make, answer or end a home call Telephone operation Call waiting on the home line Using a Bluetooth headset Make, answer or end a cell call Answer a cell call while on a home call Call waiting on the cell lineTo answer the incoming cell call To end the cell call Conference home and cell calls Answer a home call while on a cell call Handset speakerphone Volume controlSilence the ringer Mute Infrared sensor HoldHandset locator To access a number in the call log while on a Home call To access the last number redial while on a home callChain dialing Review the redial list Redial listDial a redial entry Save a redial entry to the directory Delete a redial entry Intercom Answer an incoming call during an intercom call To silence an intercom callTo end an intercom call Transfer a call Share an outside call Create a new directory entry Directory Using the telephone base Character chart Review the directory To review the directory Using a handsetAlphabetical search To start an alphabetical search Dial a directory entry To dial a directory entry Using a handsetEdit a directory entry Press /HOME or /CELL To delete an entry Delete a directory entry Information about caller ID with call waiting About caller ID Caller ID history Missed calls indicator Review the call log Memory match Dial a call log entry Make a call log entry ready to dial Save a call log entry to the directory Delete from the call log To delete all entries Using a handsetCall log display screen messages To delete a single entry Answering system and voicemail Answering system operationMessage capacity New message indication Message playback To play messages with the telephone baseTo play messages with a handset Delete all old messages Record and play memos To record a memo Using the telephone base Command Remote access Screen display messages Appendix Keypad is locked Telephone base lights Handset and telephone base indicators Handset lights Handset icons Bluetooth disconnected devices indicates that there Telephone base icons Bluetooth wireless headset on steadily when a Operation Operating time Battery Expand your telephone system Add and register a handset optionalTo register a handset To deregister all handsets Replace a handset Cannot use the keypad TroubleshootingCannot pair my cell phone to the telephone base Cannot pair my headset to the telephone base Cannot connect my headset with the telephone base Cannot put my headset in discoverable modeCannot find VTech LS6245 on my cell phone My cell phone disconnects with the telephone base Low battery shows on screen Bluetooth system busy appears on the displayPIN on the telephone base does not work My telephone does not work at all There is no dial tone Charge light is off Cannot dial out Telephone does not ring when there is an incoming call My handset beeps and is not performing normally My caller ID features are not working properly Hear other calls when using the telephoneHear noise on the cordless handset and the keys do not work Registration failed appears on the handset Caller ID entries do not match the numbers I need to dial Searching for Base shows in the handset screenCannot retrieve my voicemail messages Outgoing announcement is not clear Messages on the answering system are very difficult to hearAnswering system does not record messages Answering system does not respond to remote commands Messages on the answering system are incompleteCommon cure for electronic equipment Important safety instructions Operating range Maintenance Rbrc seal About cordless telephones What does this limited warranty cover? Warranty Other limitations FCC Part FCC, Acta and IC regulations Industry Canada Technical specifications Index Symbol Index 91-002418-030-100