Mount Base | Winegard RD-9946 specification

MOUNT BASE

INDEX	PART	DESCRIPTION	QTY
NO.	NUMBER
1	3200947	Mount Base	1
2	2160183	10-32 x 1-1/2" Hex Screw	2

Rev. 6/98

72

Image 72

Winegard RD-9946 installation manual Mount Base

Contents

Winegard Important Safeguards Not applicable to mount and antenna Table Of Contents Unpacking/Inventory Installation Requirements Rev 9/98 Installation Satellite System, RD-9946 proceed to step Do not Caulk Mount Base Ring Page Rev /99 Rev /98 Device Refer to , Page 14 for operation and installation SilverOptional RD-9911 Warning Connecttoignition+12VDC To Receiver Control Wires To Antenna Sensar TV Antenna ReceiverCH 3/4 OUT Positioner Park Move to Last Sat Search DSS ParkPress Select a or B as appropriate Press UP/DOWN arrow buttons to get Park on screen RD-9901 Remote Control Wall Plate Installation RD-9901 Remote Control Wall Plate Telephone CordPositioner Rear Panel RD-9911 Warning Device Installation/Operation RCA cable Install two AA batteries providedConnect to vehicle ground Connect to ignition +12 VDC Cable Roof-thru Plate Installation QTYDescription Use Must Perform Must Perform Locating the Satellite Pinnacle RV Digital Satellite System Models RD-9946 Important Safeguards Table of Contents Uplink Signal Programming Uplink Control Centers Introduction / HOW does Digital Satellite TV WORK?For Programming information call Dish Network DSS Finding the Satellite Method Using the City Menu System Operation Finding the SatellitesSelect a City Enter Elevation Press Select a Start Search Quit CalculatingPress Left arrow button to scroll list to the last Entry of the previous state Setting Detector Fine Tuning AzimuthMoving to Start Searching Level = Fine Tuning Elevation System has found a satellite and is fine tuning the signalCorrect Satellite Continue Search Press Select a if correct satellite was found Finding the Satellite Method Entering the Elevation Press Select B Enter elevation, Figure El Angle = Press Select B if correct satellite was not found Enter Elevation Enter Location Press Select BPress UP arrow button Press Select B Enter Location, Figure Latitude = Longitude =Press Left arrow button To decrease latitude by 1o Latitude and longitude Putting Antenna in Park Position Move to Last Satellite Move to Last Sat Manual Move Manual Movement Manual Move EditAz3 = El 3 = XXX Edit Menu Edit Search DSSEnter Code Press Select a to enter code Select Search Satellite Select Search Sat Set Motor Positions101.0 Edit Add/Edit Search Satellite Inactive EditQuit Winegard* 165.0 Quit Winegard* 165.0 EditPress Select a to enter satellite into memory Press Select a to enter new satellite as search satellitePage Remote Panel Operation Search For SatelliteSearch routine again Satellite Parking the Antenna Page Pinnacle Positioner Positioner Controls & Indicators Switch was removed 2/16/98 Programmed City Locations Power Environmental Conditions Winegard Important Safeguards Introduction No Satellite Found Antenna Reflector at Look angleLnbf Coax Center Conductor Return To Defaults Test Functions Return to Defaults Set to Defaults QuitMemory Restored Press Any Key Press Select a Set to Defaults. See Figure Positioner Does Not Respond Search Xxxxxx ParkPress Select B Park Name of search satellite Test RD-9901 Remote Control Wallplate Test LNB Test Remote Panel Test Remote Panel Elevation =Press Select B Test Remote Panel Press Select a Test Remote Panel Test Remote Panel Search LED = On Test Remote Panel Search LED = OffPress UP arrow button twice Three times Test Remote Panel Park LED = On Test Remote Panel Park LED = OffTest Remote Panel Search Key Pressed Press Right arrow button twice Test Remote Panel Park Key Pressed Test LNB Signal level, max. is Antenna = 0 dB Level =Press Select a Test LNB Min. is Make sure switch is all Way left or right depending Positioner Does Not Come On Parking System, Fail Please Check Parking System Fail Please CheckPress either Select a or B When Searching Positioner Displays Search Stopped Winegard Table of Contents Antenna Support Assembly Index Part Description QTY Number Mount Assembly Index Part Description Number Mount Base POSITIONER/ACCESSORIES ANTENNA/FEED Assembly Lnbf CABLE, Part Number For antenna mounts with a serial # of 10111 or higher