Mount Assembly | Winegard RD-9946 manual

MOUNT ASSEMBLY

Rev. 1/97

70

Image 70

Winegard RD-9946 installation manual Mount Assembly

Contents

Winegard Important Safeguards Not applicable to mount and antenna Table Of Contents Unpacking/Inventory Installation Requirements Rev 9/98 Installation Satellite System, RD-9946 proceed to step Do not Caulk Mount Base Ring Page Rev /99 Rev /98 Optional RD-9911 Warning Device Refer to , Page 14 for operation and installationSilver Connecttoignition+12VDC CH 3/4 OUT To Receiver Control Wires To AntennaSensar TV Antenna Receiver Positioner Press Select a or B as appropriate Park Move to Last SatSearch DSS Park Press UP/DOWN arrow buttons to get Park on screen RD-9901 Remote Control Wall Plate Telephone Cord RD-9901 Remote Control Wall Plate InstallationPositioner Rear Panel Connect to vehicle ground RD-9911 Warning Device Installation/OperationRCA cable Install two AA batteries provided Connect to ignition +12 VDC QTY Cable Roof-thru Plate InstallationDescription Use Must Perform Must Perform Locating the Satellite Pinnacle RV Digital Satellite System Models RD-9946 Important Safeguards Table of Contents For Programming information call Dish Network Uplink Signal Programming Uplink Control CentersIntroduction / HOW does Digital Satellite TV WORK? DSS Select a City Enter Elevation Finding the Satellite Method Using the City MenuSystem Operation Finding the Satellites Press Select a Press Left arrow button to scroll list to the last Start Search QuitCalculating Entry of the previous state Moving to Start Setting DetectorFine Tuning Azimuth Searching Level = Correct Satellite Continue Search Fine Tuning ElevationSystem has found a satellite and is fine tuning the signal Press Select a if correct satellite was found Finding the Satellite Method Entering the Elevation Press Select B Enter elevation, Figure El Angle = Press Select B if correct satellite was not found Press UP arrow button Enter Elevation Enter LocationPress Select B Press Select B Enter Location, Figure Press Left arrow button Latitude =Longitude = To decrease latitude by 1o Latitude and longitude Putting Antenna in Park Position Move to Last Satellite Move to Last Sat Manual Move Manual Move Edit Manual MovementAz3 = El 3 = XXX Enter Code Edit MenuEdit Search DSS Press Select a to enter code 101.0 Select Search SatelliteSelect Search Sat Set Motor Positions Edit Inactive Edit Add/Edit Search SatelliteQuit Press Select a to enter satellite into memory Winegard* 165.0 QuitWinegard* 165.0 Edit Press Select a to enter new satellite as search satellitePage Search routine again Remote Panel OperationSearch For Satellite Satellite Parking the Antenna Page Pinnacle Positioner Positioner Controls & Indicators Switch was removed 2/16/98 Programmed City Locations Power Environmental Conditions Winegard Important Safeguards Introduction Antenna Reflector at Look angle No Satellite FoundLnbf Coax Center Conductor Return To Defaults Memory Restored Press Any Key Test Functions Return to DefaultsSet to Defaults Quit Press Select a Set to Defaults. See Figure Search Xxxxxx Park Positioner Does Not RespondPress Select B Park Name of search satellite Test RD-9901 Remote Control Wallplate Press Select B Test Remote Panel Test LNB Test Remote PanelTest Remote Panel Elevation = Press Select a Test Remote Panel Press UP arrow button twice Test Remote Panel Search LED = OnTest Remote Panel Search LED = Off Three times Test Remote Panel Search Key Pressed Test Remote Panel Park LED = OnTest Remote Panel Park LED = Off Press Right arrow button twice Test Remote Panel Park Key Pressed Test LNB Press Select a Test LNB Signal level, max. isAntenna = 0 dB Level = Min. is Make sure switch is all Way left or right depending Positioner Does Not Come On Parking System Fail Please Check Parking System, Fail Please CheckPress either Select a or B When Searching Positioner Displays Search Stopped Winegard Table of Contents Antenna Support Assembly Index Part Description QTY Number Mount Assembly Index Part Description Number Mount Base POSITIONER/ACCESSORIES ANTENNA/FEED Assembly Lnbf CABLE, Part Number For antenna mounts with a serial # of 10111 or higher