IES-5000/5005/6000 Support Notes | ZyXEL Communications IES-6000

ports 1 and 2. The following shows the CLI commands.

IES-5000/5005/6000 Support Notes

ports 1 and 2. The following shows the CLI commands.

CI command:

TGE1> sys sw rstp enable

TGE1> sys sw rstp port enable 1

TGE1> sys sw rstp port enable 2

2. Setup IES-2000

2.1 Activating Spanning Tree protocol

This section shows how to enable STP on the IES-2000 using the web configurator. Access the web configurator and click Switch Setup in the navigation panel to display the configuration screen as shown. Then select the Rapid Spanning Tree Protocol option to enable it.

2.2 Activating Spanning Tree protocol on Ethernet ports

After you have activated STP on the system, you must activate STP on the Ethernet ports.

In the web configurator, click Port Setup in the navigation panel to display the configuration screen as shown. Click msc to display the configuration screen for the Ethernet ports on the MSC line card.

77

All contents copyright (c) 2008 ZyXEL Communications Corporation.

Image 78

ZyXEL Communications IES-6000 manual Setup IES-2000 2.1 Activating Spanning Tree protocol, IES-5000/5005/6000 Support Notes

Contents

Integrated Ethernet Switch IES-5000/5005/6000Support Notes IES-5000/5005/6000 Support Notes INDEX Triple play Application with VLC Line Card Application NotesTriple Play Triple Play scenario topology IES-5000M Main Chassis Hardware connectionsP-870H-51 MSC1000G Firmware versions IES-5000 Configure the P-870H-51 How to set the P-870H-51 to factory-default? Configure the IES-5000 1. System login 2. Configure the VLC1348G-51 a. Click Port VDSL Sub-step 1 Open VLAN setup page Sub-step 2 Join VLAN 100 to VDSL port Sub-step 3 Join VLAN 500 to VDSL port All contents copyright c 2008 ZyXEL Communications Corporation 3. Configure the MSC1000G a. Click VLAN VLAN d. Check the final VLAN setup status of the MSC1000G a. Login 4. Use ACL rule to replace the VID / Priority for the PPPoE packets b. ACL-rule profile CLI syntax 1 Create ACL profiles 5. Use MVR to configure the IPTV setting on MSC1000G a. Login 6. Configure the IGMP-Proxy and Static Query VLAN a. Login d. Check the Query VLAN status 7. Save configuration for the IPDSLAM 2. If setting is successful, result is as below Configure the ES-2024A 2. Configure VLANs 2. VLAN 500 for VoIP 3. VLAN 700 for IPTV 4. Check final status of the VLAN settings Don’t forget to click Apply to save the settings c. Set the default PVID for the relative ports in this scenario1. Click Advance Application VLAN, then choose the VLAN Port Setting 2.Set port 1 / 5 / 7’s PVID as 100 / 500 / 700 as below 1. Click Basic Setting Port Setup to call the page below 2. Click Apply at bottom to save the settings e. Save all the settings for the ES-2024A Setting up Multiple PVCs Triple play Application with ALC/SLC Line CardIES-5000 SLC-1248G or ALC-1248G 1. IES-5000 Settings 2. Prestige 660R-61P791 Settings 3. ES-2024 settings 3.1 VALN All contents copyright c 2008 ZyXEL Communications Corporation 3.2 PVID setup Set the PVIDs on port 1 and 2 to 10 and 20 respectively All contents copyright c 2008 ZyXEL Communications Corporation P‐660H‐61 IES-5000/5005/6000 Support Notes VDSL2 to ADSL2+ FallbackIES‐5000 Slot VLC1348G‐51 ADSL2+ CPE Configure the P-660H-61 1. Telnet into the P-660H-61 b. Type a name in the System Name field 2. General Setupa. Enter 1 in the Main Menu to open Menu 1 - General Setup c. Select No in the Route IP field d. Select Yes in the Bridge field 3. Remote Node Setup a. Enter 11 in the Main Menu to open Menu 11 - Remote Node Setupb. Enter 1 to configure the remote node of MyISP ISP, SUA c. Menu 11.1 - Remote Node Profile appears e. Select RFC 1483 in the Encapsulation fieldf. Select LLC-based in the Multiplexing field j. Menu 11.6 - Remote Node ATM Layer Options appears l. Press ENTER to confirm your changes Configure the VLC1348G-51 1. Login All contents copyright c 2008 ZyXEL Communications Corporation a. Click Port VDSL 2. VDSL Port Setupc. Select Enable e. Click Apply 3. PVC Setup 4. Config save a. Click Config Save on the navigation panel d. Select port e. Type 8 in VPI and 35 in VCI c. Click Diagnostic Loopback5. Check status a. Click Statistics Port Statistics f. Click the Test button to perform an OAM F5 loopback test on port All contents copyright c 2008 ZyXEL Communications Corporation IES-5000/5005/6000 Support Notes Impulse Noise Protection INP IES-5000/5005/6000 Support Notes Upstream Power Back-Off UPBO What is UPBO?PSD f PSD f FEXT-dominated environment Modes of UPBONon-FEXT dominated environment Do not apply UPBO 1. Protection of the long loop 4. Spectral mask compatibility with other services Methods of UPBO3. Improved performance of short loops IES-5000/5005/6000 Support Notes 802.1ag CFM What is CFM? MEP--Maintenance End point MD--Maintenance DomainMA--Maintenance Association CFM Terms MIP--Maintenance Intermediate Point WEB GUI Introduction 1. CFM MD Screen 2. CFM MA Screen 3. CFM MEP Screen 4. Loopback Diagnosis Disable CFM MSC1000Gswtichcfm disable Create a MD CLI Command IntroductionEnable CFM Create a MEP MSC1000G switch cfmmep set All contents copyright c 2008 ZyXEL Communications Corporation Internet Setting up different DSL port speeds to different subscribersConfiguring and applying the profiles to subscriber ports IES-5000 ALC-1248G 2. Prestige 660R-61 2.1 Menu 1 General Setup 2.2 Menu 4 Internet Access Setup2.3 Menu11.1 Remote Node Profile 2.4 Menu11.6 Remote Node ATM Layer Options IES-5000/5005/6000 Support Notes Configuring 802.1Q VLAN Setting up a VLAN 1.2 PVID settings 1.1 VLAN settings 802.1x Application TGE1 switch port pvid up1 TGE1 switch port pvid up2 Setting up Authentication Server RADIUSAuthenticator Authorized 1. Authenticator Setup IES-5000 2. RADIUS Setup Vantage 2.1 RADIUS server setup2.2 Create a User Account 3. Supplicant Setup Windows XP All contents copyright c 2008 ZyXEL Communications Corporation 4. Prestige 660R-61 Settings Syslog Server ApplicationPlease refer to the procedures described in the previous application Setting up a Syslog server 1. Installing and Running Kiwi’s Syslog ServerNetwork 2. IES-5000 settings IES-5000/5005/6000 Support Notes Ring Topology Application Setting up a Ring Environment1. IES-5000 settings 1.1 Activating Spanning Tree protocol on Ethernet Ports ports 1 and 2. The following shows the CLI commands CI command 2. Setup IES-2000 2.1 Activating Spanning Tree protocol2.2 Activating Spanning Tree protocol on Ethernet ports TGE1 sys sw rstp enable TGE1 sys sw rstp port enable Click Uplink2 to configure this port Select Rapid Spanning Tree Protocol to enable it on the port All contents copyright c 2008 ZyXEL Communications Corporation 3. ES-4024 Settings 3.1 Activating Spanning Tree protocol 4. Status Results Ethernet Port IGMP Snooping/IGMP Filtering ApplicationIGMP Router Setting up IGMP snooping/IGMP filtering 1. IES-5000 settings 1.1 Activating IGMP Snooping1.2 Setting up IGMP Filtering Limiting Internet access to users on specific DSL ports Setting up MAC Filter/Port Security1. IES-5000 settings 1.1 Configuring MAC filter 1.2 Configuring Port Security DHCP Relay Option 82 Application Setting up DHCP Relay Option Network DHCP ServerADSL/SHDSL CPE DHCP Client 2. CPE settings 3. IP Commander settings All contents copyright c 2008 ZyXEL Communications Corporation Enter a name and description for the new rule All contents copyright c 2008 ZyXEL Communications Corporation Select DHCP Option in the Keywords field All contents copyright c 2008 ZyXEL Communications Corporation In the next wizard screen, click Next to continue All contents copyright c 2008 ZyXEL Communications Corporation Click Finish to complete the wizard setup Packet Filtering After the configuration, your computer should obtain an IP address of 192.168.1.201 from the DHCP server once the computer is connected to the network Network Client Setting up Packet Filtering1. IES-5000 settings ALC-1248G/SLC 1248G Client 7- 4 accept-all 7- 5 accept-all 7- 6 accept-all 7- 7 accept-all 7-42 accept-all 7-43 accept-all 7-44 accept-all 7-45 accept-all 7-46 accept-all 7-47 accept-all 7-48 accept-all TGE1