Network DHCP Server | ZyXEL Communications IES-5005, IES-6000

Network

IES-5000/5005/6000 Support Notes

Network

DHCP

Server

IES-5000(ALC/SLC)

Port 25

ADSL/SHDSL CPE

DHCP Client

Setting up DHCP Relay Option 82

In this application example, we will show you how to configure the IES-5000 to assign a specific IP address in the client IP pool to a computer based on its DSL port, VLAN ID and the option 82 string.

For this example, assume that the computer is connected to DSL port 25 with an Option82 string of “5000” in VLAN 1. We will use the IP Commander DHCP server (192.168.1.99) to assign this computer an IP address in the client IP pool of 192.168.1.201~192.168.1.203.

1. IES-5000 settings

On the IES-5000, enable DHCP relay and specify the IP address of the DHCP server (192.168.1.99). Then enable Option82 and enter “5000” as the string.

CI command:

TGE1> ip dhcprelay enable

TGE1> ip dhcprelay relay enable

TGE1> ip dhcprelay server 1 192.168.1.99

TGE1> ip dhcprelay relayinfo add 5000

86

All contents copyright (c) 2008 ZyXEL Communications Corporation.

Image 87

ZyXEL Communications IES-5005, IES-6000 manual Network DHCP Server, ADSL/SHDSL CPE DHCP Client, Setting up DHCP Relay Option

Contents

Integrated Ethernet Switch IES-5000/5005/6000Support Notes INDEX IES-5000/5005/6000 Support Notes Triple play Application with VLC Line Card Application NotesTriple Play Triple Play scenario topology MSC1000G Hardware connectionsP-870H-51 IES-5000M Main Chassis IES-5000 Firmware versions How to set the P-870H-51 to factory-default? Configure the P-870H-51 1. System login Configure the IES-5000 2. Configure the VLC1348G-51 a. Click Port VDSL Sub-step 1 Open VLAN setup page Sub-step 2 Join VLAN 100 to VDSL port Sub-step 3 Join VLAN 500 to VDSL port IES-5000/5005/6000 Support Notes 3. Configure the MSC1000G a. Click VLAN VLAN d. Check the final VLAN setup status of the MSC1000G 4. Use ACL rule to replace the VID / Priority for the PPPoE packets a. Login b. ACL-rule profile CLI syntax 1 Create ACL profiles 5. Use MVR to configure the IPTV setting on MSC1000G a. Login 6. Configure the IGMP-Proxy and Static Query VLAN a. Login d. Check the Query VLAN status 2. If setting is successful, result is as below 7. Save configuration for the IPDSLAM Configure the ES-2024A 2. Configure VLANs 2. VLAN 500 for VoIP 3. VLAN 700 for IPTV 4. Check final status of the VLAN settings 2.Set port 1 / 5 / 7’s PVID as 100 / 500 / 700 as below c. Set the default PVID for the relative ports in this scenario1. Click Advance Application VLAN, then choose the VLAN Port Setting Don’t forget to click Apply to save the settings 2. Click Apply at bottom to save the settings 1. Click Basic Setting Port Setup to call the page below e. Save all the settings for the ES-2024A Setting up Multiple PVCs Triple play Application with ALC/SLC Line CardIES-5000 SLC-1248G or ALC-1248G 1. IES-5000 Settings 2. Prestige 660R-61P791 Settings 3.1 VALN 3. ES-2024 settings IES-5000/5005/6000 Support Notes Set the PVIDs on port 1 and 2 to 10 and 20 respectively 3.2 PVID setup IES-5000/5005/6000 Support Notes ADSL2+ CPE IES-5000/5005/6000 Support Notes VDSL2 to ADSL2+ FallbackIES‐5000 Slot VLC1348G‐51 P‐660H‐61 1. Telnet into the P-660H-61 Configure the P-660H-61 c. Select No in the Route IP field d. Select Yes in the Bridge field 2. General Setupa. Enter 1 in the Main Menu to open Menu 1 - General Setup b. Type a name in the System Name field 3. Remote Node Setup a. Enter 11 in the Main Menu to open Menu 11 - Remote Node Setupb. Enter 1 to configure the remote node of MyISP ISP, SUA c. Menu 11.1 - Remote Node Profile appears e. Select RFC 1483 in the Encapsulation fieldf. Select LLC-based in the Multiplexing field l. Press ENTER to confirm your changes j. Menu 11.6 - Remote Node ATM Layer Options appears 1. Login Configure the VLC1348G-51 IES-5000/5005/6000 Support Notes e. Click Apply 2. VDSL Port Setupc. Select Enable a. Click Port VDSL 3. PVC Setup a. Click Config Save on the navigation panel 4. Config save f. Click the Test button to perform an OAM F5 loopback test on port c. Click Diagnostic Loopback5. Check status a. Click Statistics Port Statistics d. Select port e. Type 8 in VPI and 35 in VCI IES-5000/5005/6000 Support Notes IES-5000/5005/6000 Support Notes Impulse Noise Protection INP IES-5000/5005/6000 Support Notes Upstream Power Back-Off UPBO What is UPBO?PSD f PSD f 1. Protection of the long loop Modes of UPBONon-FEXT dominated environment Do not apply UPBO FEXT-dominated environment 4. Spectral mask compatibility with other services Methods of UPBO3. Improved performance of short loops What is CFM? IES-5000/5005/6000 Support Notes 802.1ag CFM CFM Terms MD--Maintenance DomainMA--Maintenance Association MEP--Maintenance End point MIP--Maintenance Intermediate Point 1. CFM MD Screen WEB GUI Introduction 2. CFM MA Screen 3. CFM MEP Screen 4. Loopback Diagnosis Create a MEP MSC1000G switch cfmmep set CLI Command IntroductionEnable CFM Disable CFM MSC1000Gswtichcfm disable Create a MD IES-5000/5005/6000 Support Notes IES-5000 ALC-1248G Setting up different DSL port speeds to different subscribersConfiguring and applying the profiles to subscriber ports Internet 2. Prestige 660R-61 2.1 Menu 1 General Setup 2.2 Menu 4 Internet Access Setup2.3 Menu11.1 Remote Node Profile 2.4 Menu11.6 Remote Node ATM Layer Options Setting up a VLAN IES-5000/5005/6000 Support Notes Configuring 802.1Q VLAN 1.1 VLAN settings 1.2 PVID settings TGE1 switch port pvid up1 TGE1 switch port pvid up2 802.1x Application 1. Authenticator Setup IES-5000 Authentication Server RADIUSAuthenticator Authorized Setting up 2. RADIUS Setup Vantage 2.1 RADIUS server setup2.2 Create a User Account 3. Supplicant Setup Windows XP IES-5000/5005/6000 Support Notes 4. Prestige 660R-61 Settings Syslog Server ApplicationPlease refer to the procedures described in the previous application Setting up a Syslog server 1. Installing and Running Kiwi’s Syslog ServerNetwork 2. IES-5000 settings 1.1 Activating Spanning Tree protocol on Ethernet Ports Setting up a Ring Environment1. IES-5000 settings IES-5000/5005/6000 Support Notes Ring Topology Application TGE1 sys sw rstp enable TGE1 sys sw rstp port enable 2. Setup IES-2000 2.1 Activating Spanning Tree protocol2.2 Activating Spanning Tree protocol on Ethernet ports ports 1 and 2. The following shows the CLI commands CI command Select Rapid Spanning Tree Protocol to enable it on the port Click Uplink2 to configure this port IES-5000/5005/6000 Support Notes 3. ES-4024 Settings 3.1 Activating Spanning Tree protocol 4. Status Results Router IGMP Snooping/IGMP Filtering ApplicationIGMP Ethernet Port Setting up IGMP snooping/IGMP filtering 1. IES-5000 settings 1.1 Activating IGMP Snooping1.2 Setting up IGMP Filtering Limiting Internet access to users on specific DSL ports Setting up MAC Filter/Port Security1. IES-5000 settings 1.1 Configuring MAC filter DHCP Relay Option 82 Application 1.2 Configuring Port Security Setting up DHCP Relay Option Network DHCP ServerADSL/SHDSL CPE DHCP Client 3. IP Commander settings 2. CPE settings IES-5000/5005/6000 Support Notes Enter a name and description for the new rule IES-5000/5005/6000 Support Notes Select DHCP Option in the Keywords field IES-5000/5005/6000 Support Notes In the next wizard screen, click Next to continue IES-5000/5005/6000 Support Notes Click Finish to complete the wizard setup After the configuration, your computer should obtain an IP address of 192.168.1.201 from the DHCP server once the computer is connected to the network Packet Filtering Client Setting up Packet Filtering1. IES-5000 settings ALC-1248G/SLC 1248G Network Client 7- 4 accept-all 7- 5 accept-all 7- 6 accept-all 7- 7 accept-all 7-46 accept-all 7-47 accept-all 7-48 accept-all TGE1 7-42 accept-all 7-43 accept-all 7-44 accept-all 7-45 accept-all