Ryobi RY28120, RY28140 Installing the Power Head to the Attachment, Attaching the Storage Hanger

Page 11

ASSEMBLY

WARNING:

If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

WARNING:

Do not attempt to modify this product or create acces- sories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING:

To prevent accidental starting that could cause serious personal injury, always disconnect the engine spark plug wire from the spark plug when assembling parts.

INSTALLING THE POWER HEAD TO THE ATTACHMENT

See Figure 2.

WARNING:

Never install, remove, or adjust any attachment while power head is running. Failure to stop the engine can cause serious personal injury.

The attachment connects to the power head by means of a coupler device.

Loosen the knob on the coupler of the power head shaft and remove the hanger cap from the attachment.

Push in the button located on the trimmer attachment. Align the button with the guide recess on the power head coupler and slide the two shafts together. Rotate the trimmer attachment until the button locks into the positioning hole.

NOTE: If the button does not release completely in the positioning hole, the shafts are not locked into place. Slightly rotate from side to side until the button is locked into place.

Tighten the knob securely.

WARNING:

Be certain the knob is fully tightened before operating equipment; check it periodically for tightness during use to avoid serious personal injury.

REMOVING THE ATTACHMENT FROM THE POWER HEAD

Loosen the knob.

Push in the button and twist the shafts to remove and separate ends.

ATTACHING THE STORAGE HANGER

See Figure 3.

There are two ways to hang your attachment for storage.

To use the hanger cap, push in the button and place the hanger cap over end of trimmer attachment. Slightly rotate the cap from side to side until the button locks into place.

The secondary hole in the trimmer attachment can be used for hanging purposes as well.

ATTACHING THE FRONT HANDLE

See Figure 4.

Remove wing nut, washer, and bolt from the front handle.

Install the front handle onto the top side of the drive shaft housing in the area indicated by the label.

NOTE: The open side of the handle should face the operator. 

Place the bolt through the front handle.

NOTE: The hex bolt head fits inside the hex recess molded into one side of the handle.

Reinstall the washer and wing nut.

Tighten wing nut securely.

ATTACHING THE GRASS DEFLECTOR

WARNING:

The line cutting blade on the grass deflector is sharp. Avoid contact with the blade. Failure to avoid contact can result in serious personal injury.

TO ATTACH THE CURVED SHAFT GRASS DEFLECTOR - CS26

See Figure 5.

Remove hex screw, washer, and wing nut from grass deflector.

Press the grass deflector onto the bottom of the curved shaft as shown.

Insert the hex screw through the grass deflector and the bracket on the curved shaft.

Place the washer on the hex screw.

Place the wing nut on the hex screw and tighten securely.

7 — English

Image 11
Contents Toutes LES Versions Todas LAS Versiones Save this Manual for Future ReferencePage SS26 Posición Correcta Para EL Manejo DE LA Herramienta Eyelet œillet, ojillo Introduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules Symbol Name Explanation SymbolsSymbol Signal Meaning Assembly FeaturesAttaching the Front Handle Installing the Power Head to the AttachmentRemoving the Attachment from the Power Head Attaching the Storage HangerFueling and Refueling the Trimmer OperationTo Attach the Straight Shaft Grass Deflector SS26 Cutting Tips Oxygenated FuelsStarting and Stopping Operating the TrimmerGrass Deflector Line Trimming CUT-OFF Blade Advancing String Using the REEL-EASYTAP Advance SystemAdvancing the String Manually Line Replacement MaintenanceGeneral Maintenance Spool Replacement REEL-EASYTAP ADVANCE­ SystemFuel CAP, TANK, and Lines Idle Speed AdjustmentCleaning the AIR Filter Spark Plug ReplacementCarburetor Assy Maintenance ScheduleThis Product WAS Manufactured with a Catalyst Muffler AIR Filter AssySpeed. See Figure TroubleshootingGap. Refer to Spark Plug Replacement earlier Limited Warranty Statement WarrantyYour Warranty Rights and Obligations English Lire Toutes LES Instructions Règles DE Sécurité GénéralesAvertissement Règles DE Sécurité Particulières Symbole NOM Explication SymbolesAssemblage CaractéristiquesInstallation DE LA Poignée Avant Installation DU BLOC-MOTEUR SUR L’ACCESSOIRERetrait DE L’ACCESSOIRE DU Bloc Moteur Installation DE L’ANNEAU DE SuspensionLubrifiant 2 Temps DE Haute Qualité Essencelubrifiant UtilisationApprovisionnement EN Carburant Avertissement Mélange DE CarburantVoir les figures 7 à Carburants OxygénésDémarrage ET Arrêt Utilisation DU TAILLE-BORDURESVoir les figures 10 à Conseils DE CoupeAvance Manuelle DE LA Ligne DE Coupe Voir les figures 16 à Remplacement DE LigneEntretien Entretien GénéralRemisage LE Produit Remplacement DE LA BougieRéglage DU Ralenti Nettoyage DU Filtre À AIR’AIDE? Programme D’ENTRETIENNettoyage du filtre à air écran, plus haut dans ce manuel DépannageÉnoncé DE LA Garantie Limitée GarantieResponsabilités DU Propriétaire Dans LE Cadre DE LA Garantie Français LEA Todas LAS Instrucciones Reglas DE Seguridad GeneralesAdvertencia Reglas DE Seguridad Específicas Precaución Symbolo Nombre ExplicatiónSímbolos Símbolo Señal Significado PeligroArmado CaracterísticasMontaje DEL Deflector DE Pasto Advertencia Instalación DEL Cabezal Motor EN EL AditamentoMontaje DE LA ASA DE ALMACENAMIENTO Montaje DEL Mango DelanteroLlenado DEL Tanque FuncionamientoMezcla DE Combustible Vea las figuras 7 a Combustibles OxigenadosArranque Y Apagado Manejo DE LA RecortadoraVea las figuras 10 a Sugerencias Para CortarAvance Manualmente EL Hilo Cuchilla DE Corte DEL Hilo EN EL Deflector DE HierbaVea las figuras 14 a MantenimientoMantenimiento General Reabastecimiento DEL HiloAlmacenamiento DE LA Producto Ajuste DE LA Marcha LentaReemplazo DE LA Bujía Limpieza DEL Filtro DE Aire4050 Operación DEL Motor a Altitudes ElevadasEste Producto SE Fabricó CON UN Silenciador Catalítico Programa DE MantenimientoEl motor no arranca No hay chispa Solución DE ProblemasDeclaración DE LA Garantía Limitada GarantíaIv Tapa del combustible EPA solamente Notas ALL Versions / Toutes LES Versions / Todas LAS Versiones Manuel D’UTILISATION / Manual DEL OperadorCS26 RY28120 SS26 RY28140