Polaris 165 owner manual Troubleshooting, Action The float hose remains coiled

Page 7

Troubleshooting

If the Polaris cleaner regularly displays the following actions, adjustments may be necessary to restore performance. Refer to exploded parts diagram for part references.

Action: Polaris does not clean the entire pool or runs slowly.

Solution: 1. Verify that the pressure relief valve is releasing water. If it is not, clean or backwash the pool filter.

2.Check the filter screen in the quick disconnect and clean if necessary.

3.Verify that the float hose is the proper length.

4.Remove the surface module top. With the Polaris operating, verify that the randomizer tube is moving back and forth.

If it is not moving: Turn off pump, disconnect hoses, look into the mechanism and locate the filter connector inside the randomizer tube. If it is covered with debris or algae, remove the connector chamber, cylinder, and piston. Pull out the randomizer tube and clean the filter connector. If the connector is clean, replace the piston.

If it is moving: Watch the randomizer ball in the mechanism. If it does not move within 2 minutes, replace the randomizer tube and piston.

5.Verify that the water pressure is between 5 and 10 psi. A pressure tester (part #6-113-

00)is available through your participating Polaris dealer.

Action: Surface module dives under the water or leans to one side.

Solution: 1. Straighten twisted hoses.

2.Lift surface module out of the water, empty it and then shake it. If water is still heard inside, remove the top, pull out the drain plug assembly and drain the module.

3.Adjust the pressure relief valve until the surface module levels off.

4.Verify that the water pressure is between 5 and 10 psi.

A pressure tester (part #6-113-00) is available from an authorized Polaris dealer.

Action: The float hose remains coiled.

Solution: 1. See “Polaris does not clean entire pool.”

2.Lay the float hose out straight in the sun to remove the coils.

Action: Surface module moves too fast.

Solution: 1. Adjust the pressure relief valve until the surface module slows down.

2.165/Super Turtle only: Remove one of the eyeball regulators and readjust the pressure relief valve if necessary.

3.Verify that the water pressure is between 5 and 10 psi.

Action: Bag does not stay on the pool floor.

Solution: 1. Verify that the bag has been installed correctly.

2.Check for air bubbles around the jet body assembly. This may indicate air in the plumbing lines.

3.See “Surface module moves too fast.”

English

www.polarispool.com

Image 7
Contents N U a L US and Canada For customer service or supportPolaris Limited Warranty Always remove the Polaris before swimmers enter the poolIntroduction Polaris Complete CleanerInstall the Universal Wall Fitting Quick Installation InstructionsAdjust Sweep Hose to Fit Pool Depth Adjust Float Hose to Fit Pool LengthRoutine Maintenance Fine Tuning the Polaris CleanerAction Bag does not stay on the pool floor TroubleshootingAction The float hose remains coiled Action Surface module moves too fastDescription Exploded Parts DiagramEnglish Polaris Garantie Service clientèle ou assistance techniquePolaris Complets Installation du raccord mural universel UWF Instructions d’installation rapideAdaptation du tuyau à flotteurs à la longueur de la piscine Entretien normal Réglage fin du nettoyeur PolarisAction Le tuyau à flotteurs reste torsadé DépannageAction Le module de surface se déplace trop vite Description Qté Vue éclatéeDe pièce Description Kundendienst Wichtige InformationenPolaris kompletter Reiniger EinleitungInstallation der universalen Wandhalterung Quick InstallationsanleitungSchwimmschlauch je nach Poollänge einstellen Spülschlauch ja nach Pooltiefe einstellenRoutine Wartung Feineinstellung des Polaris ReinigersVorgang Beutel bleibt nicht am Boden des Pools FehlerbehebungVorgang Der Zuleitungsschlauch bleibt aufgerollt Vorgang Oberflächenmodul bewegt sich zu schnellTeile-Nr Bezeichnung Explosionsdarstellung107-00 Radkastenbausatz 110-00 Schlauchgewicht 114-00 Polaris Garantia Atención a clientes o apoyo técnicoLimpiafondos completo Polaris IntroducciónInstale el conector universal de pared Instrucciones para la instalación rápidaDe la piscina Mantenimiento periódico Ajustes menores del limpiafondos PolarisAcción La bolsa no se mantiene en el fondo de la piscina Resolución de problemasAcción La manguera de flotación se mantiene enroscada Acción El módulo de superficie se desplaza muy rápidamenteNo pieza Descripción Cant Diagrama expandido de piezasCant Pieza DescripciónPolaris Garanzia Per assistenza clienti o supportoIl dispositivo di pulizia completo Polaris IntroduzioneInstallazione del raccordo a parete universale Istruzioni per una rapida installazioneRegolazione del tubo galleggiante per adattarlo alla Della piscinaLunghezza della piscina Manutenzione regolare Ottimizzazione della messa a punto del PolarisAzione Il tubo galleggiante rimane arrotolato Individuazione e soluzione dei problemiAzione Il modulo di superficie si muove troppo rapidamente Pezzo n Descrizione Schema esploso dei pezziValvola limitatrice della pressione Informações importantes Aspirador completo Polaris IntroduçaoInstale a conexão universal de parede Instruções para instalação rápidaAjustar a mangueira flutuante de acordo com o comprimento Profundidade da piscinaManutenção de rotina Regular o aspirador PolarisAcção O saco não permanece no fundo da piscina Identificação e correcção de problemasAcção a mangueira flutuante continua enrolada Acção O módulo de superfície movimenta-se muito rapidamenteNo da Peça Descrição Quant Diagrama ilustrativo de peçasQuant No da Peça DescriçãoPage EC Declaration of Conformity