Sanyo SRT-2400DC instruction manual ON-SCREEN Menus

Page 10

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

ON-SCREEN MENUS

1When no menu is displayed on-screen, press the MENU button.

°The (SET UP 1) menu appears.

°Press the MENU button to save any setting made and switch menu screens.

NOTES:

If the (POWER FAILURE)/(DEW)/(USED TIME) menu is displayed, pressing the MENU button will return to the monitor screen display.

Press the MENU button to save any setting made and switch menu screens.

Press the PAUSE/SEARCH to save the settings and return to the monitor screen.

Within a menu, press the ] (or *) button to move the selection to the desired setting, then press the l (or j) button to enter or modify the setting.

*button

When a menu is displayed, press this button to move the cursor right.

] button

When a menu is displayed, press this button to move the cursor down.

l (or j) button

When a setting is selected within a menu, press this button to modify (decrease (or increase)) the setting or the numerical value.

Types of On-screen Display and Display Sequence

Reference pages are shown in square brackets.

SET UP 1 menu

@@@@@@@<SET@UP@1>

[11, 12]

*LANGUAGE-LANGUE-IDIOMA

 

@@@ENGLISH

 

*CLOCK@SET

 

@01-01-2000@SAT@00:00:00

 

*DAYLIGHT@SET@@@@@NO@USE

 

@@@@@@@@WEEK@MONTH@TIME

 

@ON@@@1ST-SUN@@04@02:00

 

@OFF@@LST-SUN@@10@02:00

 

SET UP 2 menu

@@@@@@@<SET@UP@2>

[13, 36]

*DISPLAY

 

@@@DATE@@@@@@@@@@@Y

 

@@@TIME@@@@@@@@@@@Y

 

@@@ALARM@COUNT@@@@Y

 

@@@SPEED@@@@@@@@@@Y

 

*BUZZER

 

@@@ALARM@IN@@@@@@@Y

 

@@@TAPE@END@@@@@@@Y

 

@@@KEY@IN@@@@@@@@@N

 

@@@WARNING@@@@@@@@Y

 

SET UP 3 menu

@@@@@@@<SET@UP@3>

[24, 33, 36, 15, 22

*ALARM@MODE@@@@@@@Y1

40, 20, 31]

*ALARM@SPEED@@@@@@8H

 

*ALARM@DURATION@@@20S

 

*VERTICAL@SYNC@@@@Y

 

*EXT@TIME@ADJ.@@@@01:00

 

*TAPE@IN@MODE@@@@@STOP

 

*TAPE@END@MODE@@@@REW

 

*TAPE@END@OUT@@@@@-3M

 

*CLOG@DETECT.@@@@@Y

 

*SERIES@REC@IN@@@@N

 

SET UP 4 menu

@@@@@@@<SET@UP@4>

[40, 15, 21, 37]

*SW@OUT

 

@@TIMING@@@@@@@@@@FIELD

 

@@FIELD@@@@@@@@@@@01

 

@@8H@@@@@@@@@@@@@@Y

 

*THREAD@CHECK@@@@@Y

 

*VIDEO@LOSS@@@@@@@N

 

*REC@SPEED@@@@@@@@N

 

*EJECT@SET

 

@@EJECT@MODE@@@@@@EJECT1

 

@@OPERATION@@@@@@@SLAVE

 

SET UP 5 menu

@@@@@@@<SET@UP@5>

[41, 43, 42, 15]

*INPUT@OUTPUT@ALARM

 

*OUTPUT@@@@@@@SERIES

 

*WARN.@OUT@@@@TRANSPORT

 

*REMOTE@@@@@@@EJECT

 

*TAPE@@@@@@@@@T-160

 

SET UP 6 menu

@@@@@@@<SET@UP@6>

[38]

*RS485

@@ADDRESS@@@@@@@000

@@TERMINATE@@@@@N

@@DATA@SPEED@@@@19200

@@STATUS@INFO@@@Y

@@ALARM@INFO@@@@Y

English

9

Image 10
Contents SRT-2400DC Precautions For the customers in CanadaLocation PrecautionsMoisture Condensation Problems Avoiding Electrical Shock and FireContents FeaturesLocations of Controls and Indicators Front PanelOperation Indicators Locations of Controls and IndicatorsDigital Display Back Panel Wvut Q O NBack Panel With the optional RS-485 board DC power source output DC power maximum cord Lengths About the memory resetConnections ON-SCREEN Menus ON-SCREEN Menus Clock setting Setting the Language and ClockLanguage Setting Setting procedure is now completedSetting the Language and Clock Automatic Daylight Saving Time AdjustmentChanging the Date/Time Display Position Changing the ON-SCREEN DisplaySelecting the On-screen Display Date and time are displayedVideo Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Correct tape thread check functionIf no tape management data is present on the tape Tape Management FunctionOperation If tape management data is present on the tapeSetting the Tape Management Function Tape Management FunctionTape Management Conflict Display Conflict display sampleWhen Tape in the SET UP 5 menu is set to T-120 Recording Speed ModeWhen Tape in the SET UP 5 menu is set to T-160 Normal RecordingRecord Pause Normal RecordingConcerning the Number of Times Tapes can be Rerecorded on Recording CheckChanges to the Recording Speed Mode During Recording Action to Take when the Video Signal DeterioratesSetting the Mode at the End of the Tape Tape Counter NotesAutorepeat Recording Repeat indicator will lightAutorepeat Recording Alarm Recording Setting Alarm RecordingAlarm Mode setting is flashing Alarm Recording Counter Display Alarm RecordingChecking the Alarm Recordings Time Alarm Search Alarm ScanProgram Timer Recording Program Timer Recording Day of the week of the 8th line is flashingTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Series Recording Series Recording SetupRecording will start in series recording mode Series recording connectionsSeries Recording Continous Loop Recording SetupLoop recording connection example with 2 VCRs Tracking Control Normal PlaybackNormal Playback Vertical Lock ControlStill Image Special PlaybackPicture Search Forward and Reverse Field AdvanceDay/Time Search Setting the Security LockDAY/TIME Search Search 01 0000 will be displayed on screenClock Adjustment Setting the BuzzerSetting procedure on the first VCR is now completed Eject terminal connection Setting the Cassette Eject ModeCassette Eject Setup Eject in terminalSettings for RS485 Terminals USE Address setting is flashing@@@@POWER@FAILURE Output Terminals Tape END OUT Terminal Output SettingSW OUT Terminal Output Setting Tape END OUT TerminalInput Output setting is flashing Series OUT/NON REC OUT terminal settingAlarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal setting Output TerminalsRemote Jack Remote control settingCOM Terminal Output Terminals Maintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001