Sanyo SRT-2400DC instruction manual Normal Recording Before starting, Recording Speed Mode

Page 20

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

NORMAL RECORDING

Normal Recording

Before starting

•Turn the power on to all devices used.

•Select the “TAPE” in the (SET UP 5) menu according to the type of the tape used.

•Load a cassette tape with erasure-prevention tab.

NOTE:

•If in the (SET UP 3) menu, TAPE IN MODE is set to “REC”, recording will start after the tape thread has been checked.

•Set the ON SCREEN switch to the “ON” position.

1Press the REC/PLAY SPEED CHANGE button to set the recording speed mode.

°The recording speed mode is displayed on-screen and on the digital display.

2Press the REC button.

°The record indicator “a” light.

°Recording starts.

°If the tape end is reached while recording, “OFF” is displayed on the digital display and the unit goes into the mode set at the “TAPE END MODE” line in the (SET UP 3) menu.

NOTES:

•If in the (SET UP 2) menu, in the BUZZER section TAPE END is set to “Y”, the buzzer will be heard as long as “OFF” is displayed on the digital display.

•To cancel the “OFF” display, press the STOP, EJECT, FF, REW or PLAY button.

3To stop recording, press the STOP button.

NOTES:

•A tape recording made on this VCR may not play back with the same degree of clarity on a real time video recorder from another manufacturer.

•If you press on the REC button and the loaded cassette has no erasure-prevention tab, the VCR will eject the cassette.

[Recording Speed Mode]

(When “ TAPE” in the (SET UP 5) menu is set to “ T-160” )

Recording

Maximum

Recording

 

 

recording

Audio

 

speed mode

interval

Tape motion

duration

recording

(hour mode)

(second)

 

(hours)

 

 

 

 

 

 

8

8

1/60

Possible

Continuous

24

24

3/60

40

40

5/60

 

 

(When “ TAPE” in the (SET UP 5) menu is set to “ T-120” )

Recording

Maximum

Recording

 

 

recording

Audio

 

speed mode

interval

Tape motion

duration

recording

(hour mode)

(second)

 

(hours)

 

 

 

 

 

 

6

6

1/60

Possible

Continuous

18

18

3/60

30

30

5/60

 

 

NOTE:

•The tape speed display will vary according to the “TAPE” setting in (SET UP 5) menu setting. In this manual, all the examples and displays used are for when “TAPE” is set to “T-160”. If set to “T-120”, please refer to the table above for the corresponding duration and displays.

For example, if the recording speed mode is “8”, then the corresponding recording speed when set to “T-120” will be “6”. And, the counter reading of 7:57:00 will be 5:57:00 when set to “T-120”.

English

19

Page 19 Page 21
Image 20
Page 19 Page 21
Contents SRT-2400DC Precautions For the customers in CanadaPrecautions Moisture Condensation ProblemsLocation Avoiding Electrical Shock and FireContents FeaturesLocations of Controls and Indicators Front PanelDigital Display Locations of Controls and IndicatorsOperation Indicators Back Panel Wvut Q O NBack Panel With the optional RS-485 board Connections About the memory resetDC power source output DC power maximum cord Lengths ON-SCREEN Menus ON-SCREEN Menus Setting the Language and Clock Language SettingClock setting Setting procedure is now completedSetting the Language and Clock Automatic Daylight Saving Time AdjustmentChanging the ON-SCREEN Display Selecting the On-screen DisplayChanging the Date/Time Display Position Date and time are displayedVideo Cassette Tapes Setting the Action to Take When a Cassette is Loaded Setting the Type of Tape UsedVideo Cassette Tapes Correct tape thread check functionTape Management Function OperationIf no tape management data is present on the tape If tape management data is present on the tapeSetting the Tape Management Function Tape Management FunctionTape Management Conflict Display Conflict display sampleRecording Speed Mode When Tape in the SET UP 5 menu is set to T-160When Tape in the SET UP 5 menu is set to T-120 Normal RecordingNormal Recording Concerning the Number of Times Tapes can be Rerecorded onRecord Pause Recording CheckChanges to the Recording Speed Mode During Recording Action to Take when the Video Signal DeterioratesSetting the Mode at the End of the Tape Tape Counter NotesAutorepeat Recording Repeat indicator will lightAutorepeat Recording Alarm Mode setting is flashing Alarm RecordingAlarm Recording Setting Checking the Alarm Recordings Time Alarm RecordingAlarm Recording Counter Display Alarm Search Alarm ScanProgram Timer Recording Program Timer Recording Day of the week of the 8th line is flashingSetting the Holidays Changing a Program Timer RecordingTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Series Recording Setup Recording will start in series recording modeSeries Recording Series recording connectionsLoop recording connection example with 2 VCRs Continous Loop Recording SetupSeries Recording Normal Playback Normal PlaybackTracking Control Vertical Lock ControlSpecial Playback Picture Search Forward and ReverseStill Image Field AdvanceSetting the Security Lock DAY/TIME SearchDay/Time Search Search 01 0000 will be displayed on screenSetting procedure on the first VCR is now completed Setting the BuzzerClock Adjustment Setting the Cassette Eject Mode Cassette Eject SetupEject terminal connection Eject in terminalSettings for RS485 Terminals USE Address setting is flashing@@@@POWER@FAILURE Tape END OUT Terminal Output Setting SW OUT Terminal Output SettingOutput Terminals Tape END OUT TerminalSeries OUT/NON REC OUT terminal setting Alarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal settingInput Output setting is flashing Output TerminalsCOM Terminal Remote control settingRemote Jack Output Terminals Maintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001
Top Page Image Contents