Sanyo SRT-2400DC instruction manual Settings for RS485 Terminals USE, Address setting is flashing

Page 39

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

SETTINGS FOR RS485 TERMINALS USE

If the VCR is going to be controlled trough a connection to the RS485 terminals, be sure to first make the settings below.

NOTES:

•Can only be used with the optional RS-485 board.

•When using the optional RS-485 board, the VCR can be controlled from a special controller.

1Press the MENU button until the (SET UP 6) menu is displayed.

°The “ADDRESS” setting is flashing.

@@@@@@@<SET@UP@6>

*RS485

@@ADDRESS@@@@@@@000

@@TERMINATE@@@@@N

@@DATA@SPEED@@@@19200

@@STATUS@INFO@@@Y

@@ALARM@INFO@@@@Y

2Press the l (or j) button to set the VCR address, then press the ] button.

5Press the l (or j) button to set the “STATUS INFO” setting, then press the ] button.

Y . . . . . . . . . . . The VCR status information (state information and warning state) are output at the RS485 terminal.

N. . . . . . . . . . . The state information is not output at the RS485 terminal. However, the warning state is output at the RS485 terminal.

6Press the l (or j) button to set the “ALARM INFO” setting.

Y . . . . . . . . . . . The VCR alarm information (alarm recording start and stop) and video loss information are output at the RS485 terminal.

N. . . . . . . . . . . The VCR alarm information (alarm recording start and stop) and video loss information are not output at the RS485 terminal.

NOTES:

•The address can be set between 000 and 127.

•Keep the button pressed and the setting will change rapidly.

3Press the l (or j) button to set the termination, then press the ] button.

N. . . . . . . . . . Not terminated Y . . . . . . . . . . Terminated

NOTE:

•The video loss information output (sent) will depend on the settings for “VIDEO LOSS” in the (SET UP 4) menu.

7Press the PAUSE/SEARCH button to save the settings.

4Press the l (or j) button to set the data transfer speed, then press the ] button.

19200 2400 4800 9600

38

English

Image 39

Contents SRT-2400DC For the customers in Canada PrecautionsAvoiding Electrical Shock and Fire PrecautionsMoisture Condensation Problems LocationFeatures ContentsFront Panel Locations of Controls and IndicatorsLocations of Controls and Indicators Operation IndicatorsDigital Display Wvut Q O N Back PanelBack Panel With the optional RS-485 board About the memory reset DC power source output DC power maximum cord LengthsConnections ON-SCREEN Menus ON-SCREEN Menus Setting procedure is now completed Setting the Language and ClockLanguage Setting Clock settingAutomatic Daylight Saving Time Adjustment Setting the Language and ClockDate and time are displayed Changing the ON-SCREEN DisplaySelecting the On-screen Display Changing the Date/Time Display PositionVideo Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Video Cassette TapesIf tape management data is present on the tape Tape Management FunctionOperation If no tape management data is present on the tapeTape Management Function Setting the Tape Management FunctionConflict display sample Tape Management Conflict DisplayNormal Recording Recording Speed ModeWhen Tape in the SET UP 5 menu is set to T-160 When Tape in the SET UP 5 menu is set to T-120Recording Check Normal RecordingConcerning the Number of Times Tapes can be Rerecorded on Record PauseAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During RecordingTape Counter Notes Setting the Mode at the End of the TapeRepeat indicator will light Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingAlarm Mode setting is flashing Alarm Recording Alarm Recording Counter DisplayChecking the Alarm Recordings Time Alarm Scan Alarm SearchProgram Timer Recording Day of the week of the 8th line is flashing Program Timer RecordingTo Cancel all Program Timer Recordings Setting the HolidaysChanging a Program Timer Recording To Cancel a Program Timer RecordingThese portions will not be recorded Series recording connections Series Recording SetupRecording will start in series recording mode Series RecordingContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Vertical Lock Control Normal PlaybackNormal Playback Tracking ControlField Advance Special PlaybackPicture Search Forward and Reverse Still Image Search 01 0000 will be displayed on screen Setting the Security Lock DAY/TIME Search Day/Time SearchSetting the Buzzer Clock AdjustmentSetting procedure on the first VCR is now completed Eject in terminal Setting the Cassette Eject ModeCassette Eject Setup Eject terminal connectionAddress setting is flashing Settings for RS485 Terminals USE@@@@POWER@FAILURE Tape END OUT Terminal Tape END OUT Terminal Output SettingSW OUT Terminal Output Setting Output TerminalsOutput Terminals Series OUT/NON REC OUT terminal settingAlarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal setting Input Output setting is flashingRemote control setting Remote JackCOM Terminal Output Terminals Maintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001