Sanyo SRT-2400DC instruction manual Setting the Tape Management Function

Page 18

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

TAPE MANAGEMENT FUNCTION

Setting the Tape Management Function

1Press the MENU button until the (TAPE MANAGEMENT) menu is displayed.

@@@@<TAPE@MANAGEMENT>

*TAPE@MANAGE.@@@@N

*PROTECT@DAY@@@@@30

*REC@PASS@SET@@@@10

*GROUP@NO.@@@@@@@OFF

*OVERRIDE@@@@@@@@N

2Press the l (or j) button to select the desired mode.

N. . . . . . The tape management function is not active.

Y. . . . . . . The tape management function is active.

When setting to “Y”, please continue with the settings below.

3Press the ] button, until the “PROTECT DAY” setting is flashing.

4Press the l (or j) button to select the desired number of days to protect the tape.

OFF . . . . The tape is not protected.

1-255 . . . Number of days to protect the tape (prevent over-recording), from the date of the last recording on the tape (or the last expected recording date (calculated using the tape length (T-120 or T-160) and the recording speed).

NOTES:

Since the last expected recording date is a calculated date (using the tape length (T-120 or T-160) and the recording speed), it may be different from the actual last recording date, this due to other settings such as (alarm recordings, program timer recordings, holiday settings).

When setting a program timer recording, the tape protection term is checked when the VCR is set to program timer recording stand-by mode.

When a program timer recording is done, the data is updated when recording starts. Even if the recording is stopped before the programmed time, the original data (last expected recording date) will remain as calculated.

5Press the ] button, until the “REC PASS SET” setting is flashing.

6Press the l (or j) button, to select the desired number of re-recording times.

OFF . . . . The number of re-recording times will not be checked.

1-100 . . . Maximum number of re-recording times.

(Refer to “Concerning the Number of Times Tapes can be Rerecorded on” on page 20.)

NOTES:

The data is updated at the beginning of the recording. Even if the recording is stopped before the end, the original data information will be considered.

During Autorepeat recording, the re-recording times count will be updated every time the tape is rewound to the beginning. Autorepeat recording will proceed even if the count exceeds the “REC PASS SET” setting. If in the BUZZER section WARNING is set to “Y”, the buzzer is heard.

7Press the ] button, until the “GROUP NO.” setting is flashing.

8Press the l (or j) button, to select the desired group number.

OFF . . . . The group number will not be checked.

1-15 . . . . Group number setting.

9Press the ] button, until the “OVERRIDE” setting is flashing.

FPress the l (or j) button, to select the desired override mode.

Y . . . . . . . In case of a conflict that prevents recording, the next operation is executed. If recording is done, then the last recording date and the re-recording times count are updated.

N. . . . . . . In case of a conflict that prevents recording, the (TAPE MANAGEMENT) menu is displayed and the conflicting setting preventing recording will flash. The only possible action is to press the EJECT button, in order to eject the tape. (Refer to “Tape Management Conflict Display”.)

GPress the PAUSE/SEARCH button to save the settings.

NOTES:

Once the tape management data is recorded on tape, it cannot be changed.

The criteria (condition) for allowing recording will be based on the data recorded on the tape and not the settings in the (TAPE MANAGEMENT) menu.

English

17

Image 18
Contents SRT-2400DC Precautions For the customers in CanadaLocation PrecautionsMoisture Condensation Problems Avoiding Electrical Shock and FireContents FeaturesLocations of Controls and Indicators Front PanelLocations of Controls and Indicators Operation IndicatorsDigital Display Back Panel Wvut Q O NBack Panel With the optional RS-485 board About the memory reset DC power source output DC power maximum cord LengthsConnections ON-SCREEN Menus ON-SCREEN Menus Clock setting Setting the Language and ClockLanguage Setting Setting procedure is now completedSetting the Language and Clock Automatic Daylight Saving Time AdjustmentChanging the Date/Time Display Position Changing the ON-SCREEN DisplaySelecting the On-screen Display Date and time are displayedVideo Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Correct tape thread check functionIf no tape management data is present on the tape Tape Management FunctionOperation If tape management data is present on the tapeSetting the Tape Management Function Tape Management FunctionTape Management Conflict Display Conflict display sampleWhen Tape in the SET UP 5 menu is set to T-120 Recording Speed ModeWhen Tape in the SET UP 5 menu is set to T-160 Normal RecordingRecord Pause Normal RecordingConcerning the Number of Times Tapes can be Rerecorded on Recording CheckChanges to the Recording Speed Mode During Recording Action to Take when the Video Signal DeterioratesSetting the Mode at the End of the Tape Tape Counter NotesRepeat indicator will light Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingAlarm Mode setting is flashing Alarm Recording Alarm Recording Counter DisplayChecking the Alarm Recordings Time Alarm Search Alarm ScanProgram Timer Recording Program Timer Recording Day of the week of the 8th line is flashingTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Series Recording Series Recording SetupRecording will start in series recording mode Series recording connectionsContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Tracking Control Normal PlaybackNormal Playback Vertical Lock ControlStill Image Special PlaybackPicture Search Forward and Reverse Field AdvanceDay/Time Search Setting the Security LockDAY/TIME Search Search 01 0000 will be displayed on screenSetting the Buzzer Clock AdjustmentSetting procedure on the first VCR is now completed Eject terminal connection Setting the Cassette Eject ModeCassette Eject Setup Eject in terminalSettings for RS485 Terminals USE Address setting is flashing@@@@POWER@FAILURE Output Terminals Tape END OUT Terminal Output SettingSW OUT Terminal Output Setting Tape END OUT TerminalInput Output setting is flashing Series OUT/NON REC OUT terminal settingAlarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal setting Output TerminalsRemote control setting Remote JackCOM Terminal Output Terminals Maintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001