Sanyo SRT-2400DC instruction manual Precautions, Location, Avoiding Electrical Shock and Fire

Page 3

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

PRECAUTIONS

Location

For safe operation and satisfactory performance of your VCR, keep the following in mind when selecting a place for its installation:

•Shield it from direct sunlight and keep it away from sources of intense heat.

•Avoid dusty or humid places.

•Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes of the VCR. Do not place the unit on a carpet because this will block the ventilation holes.

•Install the VCR in a horizontal position only.

•Avoid locations subject to strong vibrations.

•Avoid moving the VCR between cold and hot locations (see “Moisture Condensation Problems”, this page).

•Do not place the VCR directly on top of the TV, as this may cause playback or recording problems.

Avoiding Electrical Shock and Fire

•Do not handle the power cord with wet hands.

•If any liquid is spilled on the VCR, unplug the power cord immediately and have the unit inspected at a factory-authorized service center.

•Do not place anything directly on top of this VCR.

Moisture Condensation Problems

Cause:

When the VCR is first installed, moved from a cold area to a warm area or placed in a location with high humidity, dew (moisture) may form in the unit. The Dew indicator (À) blinks. If you operate the VCR with dew inside, damage may result.

Prevention:

1Do not operate the VCR for approximately 2 hours.

When the VCR reaches room temperature, the Dew indicator (À) will turn off and the VCR will be ready to operation.

2

English

Image 3

Contents SRT-2400DC For the customers in Canada PrecautionsAvoiding Electrical Shock and Fire PrecautionsMoisture Condensation Problems LocationFeatures ContentsFront Panel Locations of Controls and IndicatorsLocations of Controls and Indicators Operation IndicatorsDigital Display Wvut Q O N Back PanelBack Panel With the optional RS-485 board About the memory reset DC power source output DC power maximum cord LengthsConnections ON-SCREEN Menus ON-SCREEN Menus Setting procedure is now completed Setting the Language and ClockLanguage Setting Clock settingAutomatic Daylight Saving Time Adjustment Setting the Language and ClockDate and time are displayed Changing the ON-SCREEN DisplaySelecting the On-screen Display Changing the Date/Time Display PositionVideo Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Video Cassette TapesIf tape management data is present on the tape Tape Management FunctionOperation If no tape management data is present on the tapeTape Management Function Setting the Tape Management FunctionConflict display sample Tape Management Conflict DisplayNormal Recording Recording Speed ModeWhen Tape in the SET UP 5 menu is set to T-160 When Tape in the SET UP 5 menu is set to T-120Recording Check Normal RecordingConcerning the Number of Times Tapes can be Rerecorded on Record PauseAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During RecordingTape Counter Notes Setting the Mode at the End of the TapeRepeat indicator will light Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingAlarm Mode setting is flashing Alarm Recording Alarm Recording Counter DisplayChecking the Alarm Recordings Time Alarm Scan Alarm SearchProgram Timer Recording Day of the week of the 8th line is flashing Program Timer RecordingTo Cancel all Program Timer Recordings Setting the HolidaysChanging a Program Timer Recording To Cancel a Program Timer RecordingThese portions will not be recorded Series recording connections Series Recording SetupRecording will start in series recording mode Series RecordingContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Vertical Lock Control Normal PlaybackNormal Playback Tracking ControlField Advance Special PlaybackPicture Search Forward and Reverse Still ImageSearch 01 0000 will be displayed on screen Setting the Security LockDAY/TIME Search Day/Time SearchSetting the Buzzer Clock AdjustmentSetting procedure on the first VCR is now completed Eject in terminal Setting the Cassette Eject ModeCassette Eject Setup Eject terminal connectionAddress setting is flashing Settings for RS485 Terminals USE@@@@POWER@FAILURE Tape END OUT Terminal Tape END OUT Terminal Output SettingSW OUT Terminal Output Setting Output TerminalsOutput Terminals Series OUT/NON REC OUT terminal settingAlarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal setting Input Output setting is flashingRemote control setting Remote JackCOM Terminal Output Terminals Maintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001