Sanyo SRT-2400DC instruction manual Video Cassette Tapes, Correct tape thread check function

Page 16

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

VIDEO CASSETTE TAPES

Correct tape thread check function

If the correct tape thread check function is on, after the cassette tape is loaded, a mechanism will operate for about 12 seconds to check that the tape has been threaded (loaded) correctly and the cassette indicator “o” will blink during that period. If the tape is not loaded properly, the cassette will be ejected.

NOTES:

•This function checks to make sure that the cassette has been correctly loaded. It is recommended to use this function to make sure the recordings are conducted reliably.

•If during the tape thread check operation, the REC, PLAY, FF, REW or STOP button is pressed, the command will only be executed after the tape thread has been checked. Only the EJECT button will operate while the tape thread is being checked.

•If in the (SET UP 3) menu “TAPE IN MODE” is set to “REC”, the recording indicator “a” will light during the while the tape thread is checked. However, recording will only start after the tape thread check is completed. To cancel recording, press the STOP button.

1Press the MENU button until the (SET UP 4) menu is displayed.

@@@@@@@<SET@UP@4>

*SW@OUT

@@TIMING@@@@@@@@@@FIELD

@@FIELD@@@@@@@@@@@01

@@8H@@@@@@@@@@@@@@Y

*THREAD@CHECK@@@@@Y

*VIDEO@LOSS@@@@@@@N

*REC@SPEED@@@@@@@@N

*EJECT@SET

@@EJECT@MODE@@@@@@EJECT1

@@OPERATION@@@@@@@SLAVE

2Press the ] button, until the “THREAD CHECK” setting is flashing.

3Press the l (or j) button to set the desired mode.

Y. . . . . . . . . . The correct tape thread check function is on

N. . . . . . . . . . The correct tape thread check function is off

4 Press the PAUSE/SEARCH button to save the setting.

Setting the Action to Take When a Cassette is Loaded

In the (SET UP 3) menu, you can set the mode the VCR will go into when a cassette is loaded.

1Press the MENU button until the (SET UP 3) menu is displayed.

@@@@@@@<SET@UP@3>

*ALARM@MODE@@@@@@@Y1

*ALARM@SPEED@@@@@@8H

*ALARM@DURATION@@@20S

*VERTICAL@SYNC@@@@Y

*EXT@TIME@ADJ.@@@@01:00

*TAPE@IN@MODE@@@@@STOP

*TAPE@END@MODE@@@@REW *TAPE@END@OUT@@@@@-3M *CLOG@DETECT.@@@@@Y *SERIES@REC@IN@@@@N

2Press the ] button, until the “TAPE IN MODE” setting is flashing.

3Press the l (or j) button to set the desired mode.

STOP

Stays in stop mode

REC

Goes into recording mode

4Press the PAUSE/SEARCH button to save the setting.

Setting the Type of Tape Used

1Press the MENU button until the (SET UP 5) menu is displayed.

@@@@@@@<SET@UP@5>

*INPUT@OUTPUT@ALARM

*OUTPUT@@@@@@@SERIES

*WARN.@OUT@@@@TRANSPORT

*REMOTE@@@@@@@EJECT *TAPE@@@@@@@@@T-160

2Press the ] button, until the “TAPE” setting is flashing.

3Press the l (or j) button, to select the tape used.

T-160 . . . . . . . when using an T-160 cassette tape

T-120 . . . . . . . when using an T-120 cassette tape

4Press the PAUSE/SEARCH button to save the setting.

English

15

Page 15 Page 17
Image 16
Page 15 Page 17
Contents SRT-2400DC Precautions For the customers in CanadaPrecautions Moisture Condensation ProblemsLocation Avoiding Electrical Shock and FireContents FeaturesLocations of Controls and Indicators Front PanelOperation Indicators Locations of Controls and IndicatorsDigital Display Back Panel Wvut Q O NBack Panel With the optional RS-485 board DC power source output DC power maximum cord Lengths About the memory resetConnections ON-SCREEN Menus ON-SCREEN Menus Setting the Language and Clock Language SettingClock setting Setting procedure is now completedSetting the Language and Clock Automatic Daylight Saving Time AdjustmentChanging the ON-SCREEN Display Selecting the On-screen DisplayChanging the Date/Time Display Position Date and time are displayedVideo Cassette Tapes Setting the Action to Take When a Cassette is Loaded Setting the Type of Tape UsedVideo Cassette Tapes Correct tape thread check functionTape Management Function OperationIf no tape management data is present on the tape If tape management data is present on the tapeSetting the Tape Management Function Tape Management FunctionTape Management Conflict Display Conflict display sampleRecording Speed Mode When Tape in the SET UP 5 menu is set to T-160When Tape in the SET UP 5 menu is set to T-120 Normal RecordingNormal Recording Concerning the Number of Times Tapes can be Rerecorded onRecord Pause Recording CheckChanges to the Recording Speed Mode During Recording Action to Take when the Video Signal DeterioratesSetting the Mode at the End of the Tape Tape Counter NotesAutorepeat Recording Repeat indicator will lightAutorepeat Recording Alarm Recording Setting Alarm RecordingAlarm Mode setting is flashing Alarm Recording Counter Display Alarm RecordingChecking the Alarm Recordings Time Alarm Search Alarm ScanProgram Timer Recording Program Timer Recording Day of the week of the 8th line is flashingSetting the Holidays Changing a Program Timer RecordingTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Series Recording Setup Recording will start in series recording modeSeries Recording Series recording connectionsSeries Recording Continous Loop Recording SetupLoop recording connection example with 2 VCRs Normal Playback Normal PlaybackTracking Control Vertical Lock ControlSpecial Playback Picture Search Forward and ReverseStill Image Field AdvanceSetting the Security Lock DAY/TIME SearchDay/Time Search Search 01 0000 will be displayed on screenClock Adjustment Setting the BuzzerSetting procedure on the first VCR is now completed Setting the Cassette Eject Mode Cassette Eject SetupEject terminal connection Eject in terminalSettings for RS485 Terminals USE Address setting is flashing@@@@POWER@FAILURE Tape END OUT Terminal Output Setting SW OUT Terminal Output SettingOutput Terminals Tape END OUT TerminalSeries OUT/NON REC OUT terminal setting Alarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal settingInput Output setting is flashing Output TerminalsRemote Jack Remote control settingCOM Terminal Output Terminals Maintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001
Top Page Image Contents