Sanyo SRT-2400DC instruction manual Alarm Recording Setting, Alarm Mode setting is flashing

Page 25

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

ALARM RECORDING

By connecting the ALARM IN/CLOCK IN terminal to a door switch, an interphone, etc., a recording can be done only when necessary.

Alarm Recording Setting

Alarm recording is performed when there is an input (trigger) at the ALARM IN/CLOCK IN terminal, “AL” is displayed on the digital display.

•To do alarm recording, “INPUT OUTPUT” in the (SET UP 5) menu must be set to “ALARM”.

•Make all necessary connections.

•The alarm triggers are received while in recording and stop modes.

•Follow the Before starting steps, under “NORMAL RECORDING”.

1Press the MENU button until the (SET UP 3) menu is displayed.

°The “ALARM MODE” setting is flashing.

@@@@@@@<SET@UP@3>

*ALARM@MODE@@@@@@@Y1

*ALARM@SPEED@@@@@@8H

*ALARM@DURATION@@@20S

*VERTICAL@SYNC@@@@Y

*EXT@TIME@ADJ.@@@@01:00

*TAPE@IN@MODE@@@@@STOP

*TAPE@END@MODE@@@@REW *TAPE@END@OUT@@@@@-3M *CLOG@DETECT.@@@@@Y *SERIES@REC@IN@@@@N

2Press the l (or j) button to set the desired alarm recording mode, then press the ] button.

Y1. . . . . . Alarm recording is done when there is an alarm trigger.

Y2. . . . . . Alarm recording is done only when there is an alarm trigger during programmed timer recording.

Y3. . . . . . Alarm recording is done only if there is an alarm trigger and the VCR is not in programmed timer recording mode.

Y4. . . . . . Alarm recording is done only when there is an alarm trigger during programmed timer recording duration. Timer recording is not possible.

N. . . . . . Alarm recording is not performed even if there is an alarm trigger.

3Press the l (or j) button to select the desired recording speed, then press the ] button.

8H (6H). . . . . . 8-hour (6-hour) mode recording

24H (18H) . . . 24-hour (18-hour) mode recording

40H (30H) . . . 40-hour (30-hour) mode recording

NC . . . . . . . . . Recording at the speed already set

NOTE:

•Indicated in brackets are the settings for when “TAPE” in the (SET UP 5) menu is set to “T-120”.

4Press the l (or j) button, to select the desired alarm recording duration (20S, 40S, 1M, 2M, 3M, 4M, 5M, or CC).

20S-5M . . . . . . Recording only for the displayed duration

CC. . . . . . . . . Recording as long as the alarm signal is being input (minimum 5 seconds)

5Press the PAUSE/SEARCH button to save the settings.

NOTES:

•During alarm recording all buttons are disabled.

•If “OFF” is displayed on the digital display, alarm recording is not possible in order to prevent the recorded tape to be recorded over.

To cancel the “OFF” display, press the STOP, EJECT, FF, REW or PLAY button.

•If an alarm trigger is received while alarm recording is in progress, recording duration for the second alarm will be calculated from that point. The alarm counter will register the alarm, but it will not be found during an alarm scan and alarm search.

•If there is a power failure during alarm recording, and the power is restored within the recording set duration, alarm recording will continue.

•If the alarm recording duration is short, the alarms may not be found during an alarm scan or an alarm search. If the alarms are going to be reviewed using alarm scan or alarm search, then in 8-hour mode, 20-second or more recording duration should be used.

•To do alarm recording during series recording, set “ALARM MODE” to “Y1” or “Y3”. Alarm recording will be conducted only if the VCR is recording.

24

English

Page 24 Page 26
Image 25
Page 24 Page 26
Contents SRT-2400DC For the customers in Canada PrecautionsMoisture Condensation Problems PrecautionsLocation Avoiding Electrical Shock and FireFeatures ContentsFront Panel Locations of Controls and IndicatorsOperation Indicators Locations of Controls and IndicatorsDigital Display Wvut Q O N Back PanelBack Panel With the optional RS-485 board DC power source output DC power maximum cord Lengths About the memory resetConnections ON-SCREEN Menus ON-SCREEN Menus Language Setting Setting the Language and ClockClock setting Setting procedure is now completedAutomatic Daylight Saving Time Adjustment Setting the Language and ClockSelecting the On-screen Display Changing the ON-SCREEN DisplayChanging the Date/Time Display Position Date and time are displayedVideo Cassette Tapes Setting the Type of Tape Used Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Correct tape thread check functionOperation Tape Management FunctionIf no tape management data is present on the tape If tape management data is present on the tapeTape Management Function Setting the Tape Management FunctionConflict display sample Tape Management Conflict DisplayWhen Tape in the SET UP 5 menu is set to T-160 Recording Speed ModeWhen Tape in the SET UP 5 menu is set to T-120 Normal RecordingConcerning the Number of Times Tapes can be Rerecorded on Normal RecordingRecord Pause Recording CheckAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During RecordingTape Counter Notes Setting the Mode at the End of the TapeAutorepeat Recording Repeat indicator will lightAutorepeat Recording Alarm Recording Setting Alarm RecordingAlarm Mode setting is flashing Alarm Recording Counter Display Alarm RecordingChecking the Alarm Recordings Time Alarm Scan Alarm SearchProgram Timer Recording Day of the week of the 8th line is flashing Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording will start in series recording mode Series Recording SetupSeries Recording Series recording connectionsSeries Recording Continous Loop Recording SetupLoop recording connection example with 2 VCRs Normal Playback Normal PlaybackTracking Control Vertical Lock ControlPicture Search Forward and Reverse Special PlaybackStill Image Field AdvanceDAY/TIME Search Setting the Security LockDay/Time Search Search 01 0000 will be displayed on screenClock Adjustment Setting the BuzzerSetting procedure on the first VCR is now completed Cassette Eject Setup Setting the Cassette Eject ModeEject terminal connection Eject in terminalAddress setting is flashing Settings for RS485 Terminals USE@@@@POWER@FAILURE SW OUT Terminal Output Setting Tape END OUT Terminal Output SettingOutput Terminals Tape END OUT TerminalAlarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal setting Series OUT/NON REC OUT terminal settingInput Output setting is flashing Output TerminalsRemote Jack Remote control settingCOM Terminal Output Terminals Maintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001
Top Page Image Contents