Sanyo SRT-2400DC instruction manual DAY/TIME Search, Setting the Security Lock, Day/Time Search

Page 36

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

DAY/TIME SEARCH

Day/Time Search

1Press the PAUSE/SEARCH button three times during stop mode.

°“T/D SEARCH 01 00:00” will be displayed on screen.

1H22M33S

T/D@SEARCH

01@@00:00

DAY@TIME

2Press the l (or j) button to set the desired day, then press the * button.

3Press the l (or j) button to set the desired hour, then press the * button.

4Press the l (or j) button to set the desired minutes.

NOTES:

•The setting can be made in 10 minutes increments only.

•For recordings made on other VCRs, the exact time may not be found even if the minutes are entered. For tapes recorded on older models of VCRs produced by this company (the ones without a minutes setting for the day/time search function), make sure to set the minutes to “00”.

5Press the FF (or REW) button.

°The desired day/time is searched and a still image of the recording will appear on-screen.

6Press the PLAY button.

°Playback will start.

NOTES:

•If during a search the end of the tape is reached, the tape will rewind and stop. If the beginning of the tape is reached, it will stop.

•The alarm and day/time data are recorded on the tape in a similar format. If they overlap, the alarm data will have the priority. Therefore, when searching for a day/time when an alarm recording was done, the day/time search will not stop at the desired location. In such a case, use alarm scan to find the desired recording location.

•The day/time search function may not operate correctly if searching for a timer recording time or if the clock on the recording VCR has been adjusted using the CLOCK ADJUSTMENT function.

•If a recording on a tape extends for over a one month period, the same day may be present twice on the tape. If such a day is searched, since there is no month search setting, the desired day may not be found.

SETTING THE SECURITY LOCK

The security lock function is designed to prevent accidental stopping of recording if the STOP button is pressed inadvertently.

1While holding the TRACKING/V.STILL + button, press the REC/PLAY SPEED CHANGE button.

°“x” is displayed on the digital display.

To cancel the security lock, while holding the TRACKING/V.STILL + button, press the REC/PLAY SPEED CHANGE button, “x” will be erased from the digital display.

NOTES:

•While the security lock is engaged all commands, except the one to cancel the security lock, are disabled.

•The security lock cannot be engaged while a menu is displayed.

English

35

Page 35 Page 37
Image 36
Page 35 Page 37
Contents SRT-2400DC Precautions For the customers in CanadaPrecautions Moisture Condensation ProblemsLocation Avoiding Electrical Shock and FireContents FeaturesLocations of Controls and Indicators Front PanelLocations of Controls and Indicators Operation IndicatorsDigital Display Back Panel Wvut Q O NBack Panel With the optional RS-485 board About the memory reset DC power source output DC power maximum cord LengthsConnections ON-SCREEN Menus ON-SCREEN Menus Setting the Language and Clock Language SettingClock setting Setting procedure is now completedSetting the Language and Clock Automatic Daylight Saving Time AdjustmentChanging the ON-SCREEN Display Selecting the On-screen DisplayChanging the Date/Time Display Position Date and time are displayedVideo Cassette Tapes Setting the Action to Take When a Cassette is Loaded Setting the Type of Tape UsedVideo Cassette Tapes Correct tape thread check functionTape Management Function OperationIf no tape management data is present on the tape If tape management data is present on the tapeSetting the Tape Management Function Tape Management FunctionTape Management Conflict Display Conflict display sampleRecording Speed Mode When Tape in the SET UP 5 menu is set to T-160When Tape in the SET UP 5 menu is set to T-120 Normal RecordingNormal Recording Concerning the Number of Times Tapes can be Rerecorded onRecord Pause Recording CheckChanges to the Recording Speed Mode During Recording Action to Take when the Video Signal DeterioratesSetting the Mode at the End of the Tape Tape Counter NotesRepeat indicator will light Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingAlarm Mode setting is flashing Alarm Recording Alarm Recording Counter DisplayChecking the Alarm Recordings Time Alarm Search Alarm ScanProgram Timer Recording Program Timer Recording Day of the week of the 8th line is flashingSetting the Holidays Changing a Program Timer RecordingTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Series Recording Setup Recording will start in series recording modeSeries Recording Series recording connectionsContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Normal Playback Normal PlaybackTracking Control Vertical Lock ControlSpecial Playback Picture Search Forward and ReverseStill Image Field AdvanceSetting the Security Lock DAY/TIME SearchDay/Time Search Search 01 0000 will be displayed on screenSetting the Buzzer Clock AdjustmentSetting procedure on the first VCR is now completed Setting the Cassette Eject Mode Cassette Eject SetupEject terminal connection Eject in terminalSettings for RS485 Terminals USE Address setting is flashing@@@@POWER@FAILURE Tape END OUT Terminal Output Setting SW OUT Terminal Output SettingOutput Terminals Tape END OUT TerminalSeries OUT/NON REC OUT terminal setting Alarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal settingInput Output setting is flashing Output TerminalsRemote control setting Remote JackCOM Terminal Output Terminals Maintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001
Top Page Image Contents