Sanyo SRT-2400DC instruction manual Video Cassette Tapes

Page 15

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

VIDEO CASSETTE TAPES

Use only video cassette tapes bearing the w logo. This VCR was primarily designed for use with T-120 or T-160 cassette tapes, it is recommended to use T-120 or T-160 standard grade VHS video cassette tapes for optimal performance.

Loading

1Place the cassette, label side up, in the loading slot. Gently push the center of the cassette until it is loaded automatically.

Handling Cassette Tapes

The cassette tapes should always be stored vertically, in their cases, away from high temperatures, magnetic fields, direct sunlight, dirt, dust and locations subject to mold formation.

Do not tamper with the cassette mechanism and never touch the tape with your fingers.

Protect the cassette tapes from shocks or strong vibrations.

To Protect your Recordings

After having recorded a tape, if you wish to keep the recording, use a flathead screwdriver to break off the erasure-prevention tab on the cassette.

To record again on a tape without erasure-prevention tab, cover the hole with adhesive tape.

Erasure-prevention tab

Precautions concerning the video cassette tapes

Do not use tapes that are damaged, tapes that have been cut and repaired or tapes that have been altered in any way.

Some rewinders may entangle the tape, and therefore their use is not recommended.

When tapes are recorded over and over again, the recording quality will deteriorate. Refer to “Concerning the Number of Times Tapes can be Rerecorded on” on page 20, and replace the tape with a new tape as required.

°The time display will switch to the reset counter “0:00:00” display.

°After the cassette tape is loaded, a mechanism will operate for about 12 seconds to check that

the tape has been threaded correctly and the cassette indicator owill blink during that period.

°When the cassette is loaded, if the tape has been threaded correctly, the cassette indicator owill light on the digital display.

NOTE:

If you try to record on a cassette without erasure-prevention tab, the VCR will eject the cassette.

Unloading

1In stop mode, press the EJECT button.

°The cassette is automatically ejected.

NOTES:

Do not insert any object in the cassette loading slot, as that may cause injury and damages to the VCR.

If your hand gets stuck in the cassette loading slot, unplug the power cord and consult the dealer where the unit was bought. Do not forcibly pull the hand out as that may cause severe injuries.

14

English

Image 15
Contents SRT-2400DC For the customers in Canada PrecautionsAvoiding Electrical Shock and Fire PrecautionsMoisture Condensation Problems LocationFeatures ContentsFront Panel Locations of Controls and IndicatorsLocations of Controls and Indicators Operation IndicatorsDigital Display Wvut Q O N Back PanelBack Panel With the optional RS-485 board About the memory reset DC power source output DC power maximum cord LengthsConnections ON-SCREEN Menus ON-SCREEN Menus Setting procedure is now completed Setting the Language and ClockLanguage Setting Clock settingAutomatic Daylight Saving Time Adjustment Setting the Language and ClockDate and time are displayed Changing the ON-SCREEN DisplaySelecting the On-screen Display Changing the Date/Time Display PositionVideo Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Video Cassette TapesIf tape management data is present on the tape Tape Management FunctionOperation If no tape management data is present on the tapeTape Management Function Setting the Tape Management FunctionConflict display sample Tape Management Conflict DisplayNormal Recording Recording Speed ModeWhen Tape in the SET UP 5 menu is set to T-160 When Tape in the SET UP 5 menu is set to T-120Recording Check Normal RecordingConcerning the Number of Times Tapes can be Rerecorded on Record PauseAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During RecordingTape Counter Notes Setting the Mode at the End of the TapeRepeat indicator will light Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingAlarm Mode setting is flashing Alarm Recording Alarm Recording Counter DisplayChecking the Alarm Recordings Time Alarm Scan Alarm SearchProgram Timer Recording Day of the week of the 8th line is flashing Program Timer RecordingTo Cancel all Program Timer Recordings Setting the HolidaysChanging a Program Timer Recording To Cancel a Program Timer RecordingThese portions will not be recorded Series recording connections Series Recording SetupRecording will start in series recording mode Series RecordingContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Vertical Lock Control Normal PlaybackNormal Playback Tracking ControlField Advance Special PlaybackPicture Search Forward and Reverse Still ImageSearch 01 0000 will be displayed on screen Setting the Security LockDAY/TIME Search Day/Time SearchSetting the Buzzer Clock AdjustmentSetting procedure on the first VCR is now completed Eject in terminal Setting the Cassette Eject ModeCassette Eject Setup Eject terminal connectionAddress setting is flashing Settings for RS485 Terminals USE@@@@POWER@FAILURE Tape END OUT Terminal Tape END OUT Terminal Output SettingSW OUT Terminal Output Setting Output TerminalsOutput Terminals Series OUT/NON REC OUT terminal settingAlarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal setting Input Output setting is flashingRemote control setting Remote JackCOM Terminal Output Terminals Maintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001