Sanyo SRT-2400DC instruction manual Output Terminals, Tape END OUT Terminal, SW OUT Terminal

Page 41

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

OUTPUT TERMINALS

TAPE END OUT Terminal

•During recording, when the end of the tape is reached or when the tape counter reading indicates 7 hours 57 minutes or more, the output becomes 0V (Low).

•To reset the output, press the STOP or EJECT button.

•During autorepeat recording, when the end of the tape is reached, the output becomes 0V (Low) for about 2 seconds only.

Tape end or 7:57:00

Output reset

5V (H)

(Output impedance: 5.7 kΩ) 0V (L)

TAPE END OUT Terminal Output Setting

1Press the MENU button until the (SET UP 3) menu is displayed.

@@@@@@@<SET@UP@3>

*ALARM@MODE@@@@@@@Y1

*ALARM@SPEED@@@@@@8H

*ALARM@DURATION@@@20S

*VERTICAL@SYNC@@@@Y

*EXT@TIME@ADJ.@@@@01:00

*TAPE@IN@MODE@@@@@STOP

*TAPE@END@MODE@@@@REW *TAPE@END@OUT@@@@@-3M *CLOG@DETECT.@@@@@Y *SERIES@REC@IN@@@@N

2Press the ] button until the “TAPE END OUT” setting is flashing.

3Press the l (or j) button, to select the desired output mode.

–3M . . . . . . . . The output becomes 0 V (Low) when the tape counter reaches “7:57:00” and/or when the tape reaches the end.

END . . . . . . . . The output becomes 0 V (Low) when the tape reaches the end.

4Press the PAUSE/SEARCH button to save the setting.

SW OUT Terminal

When recording, a pulse signal is output at the SW OUT terminal.

This terminal is usually connected to the switch input (SW IN) of devices like a camera switcher unit, or a quad compressor.

FIELD: 16.7 msec.

FRAME: 5 msec.

5V (H)

(Output impedance: 5.7 kΩ) 0V (L)

SW OUT Terminal Output Setting

1Press the MENU button until the (SET UP 4) menu is displayed.

@@@@@@@<SET@UP@4>

*SW@OUT

@@TIMING@@@@@@@@@@FIELD

@@FIELD@@@@@@@@@@@01

@@8H@@@@@@@@@@@@@@Y

*THREAD@CHECK@@@@@Y

*VIDEO@LOSS@@@@@@@N

*REC@SPEED@@@@@@@@N

*EJECT@SET

@@EJECT@MODE@@@@@@EJECT1

@@OPERATION@@@@@@@SLAVE

2Press the l (or j) button to set “FIELD” or “FRAME”, then press the ] button.

FIELD . . . . . . . 1 pulse is output after each set number of fields.

FRAME. . . . . . 1 pulse is output after each set number of frames.

3Press the l (or j) button to set the desired pulse signal interval, then press the ] button.

•If “TIMING” is set to FRAME (see step 2), “FRAME” will be indicated instead of “FIELD”.

Available settings are:

FIELD . . . . . . . 01, 02, 03, 04, 05, 10, 30 or 60 field

FRAME. . . . . . 01, 02, 03, 04, 05, 10, 30 or 60 frame

4Press the l (or j) button to set the desired “8H (or 6H)” mode.

•If the “TAPE” in the (SET UP 5) menu is set to “T-120”, “6H” will be indicated instead of “8H”.

Y . . . . . . . . . . . When recording in 8-hour (or 6-hour) mode, a pulse signal is output.

N. . . . . . . . . . . When recording in 8-hour (or 6-hour) mode, a pulse signal is not output.

5Press the PAUSE/SEARCH button to save the settings.

40

English

Page 40 Page 42
Image 41
Page 40 Page 42
Contents SRT-2400DC For the customers in Canada PrecautionsMoisture Condensation Problems PrecautionsLocation Avoiding Electrical Shock and FireFeatures ContentsFront Panel Locations of Controls and IndicatorsDigital Display Locations of Controls and IndicatorsOperation Indicators Wvut Q O N Back PanelBack Panel With the optional RS-485 board Connections About the memory resetDC power source output DC power maximum cord Lengths ON-SCREEN Menus ON-SCREEN Menus Language Setting Setting the Language and ClockClock setting Setting procedure is now completedAutomatic Daylight Saving Time Adjustment Setting the Language and ClockSelecting the On-screen Display Changing the ON-SCREEN DisplayChanging the Date/Time Display Position Date and time are displayedVideo Cassette Tapes Setting the Type of Tape Used Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Correct tape thread check functionOperation Tape Management FunctionIf no tape management data is present on the tape If tape management data is present on the tapeTape Management Function Setting the Tape Management FunctionConflict display sample Tape Management Conflict DisplayWhen Tape in the SET UP 5 menu is set to T-160 Recording Speed ModeWhen Tape in the SET UP 5 menu is set to T-120 Normal RecordingConcerning the Number of Times Tapes can be Rerecorded on Normal RecordingRecord Pause Recording CheckAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During RecordingTape Counter Notes Setting the Mode at the End of the TapeAutorepeat Recording Repeat indicator will lightAutorepeat Recording Alarm Mode setting is flashing Alarm RecordingAlarm Recording Setting Checking the Alarm Recordings Time Alarm RecordingAlarm Recording Counter Display Alarm Scan Alarm SearchProgram Timer Recording Day of the week of the 8th line is flashing Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording will start in series recording mode Series Recording SetupSeries Recording Series recording connectionsLoop recording connection example with 2 VCRs Continous Loop Recording SetupSeries Recording Normal Playback Normal PlaybackTracking Control Vertical Lock ControlPicture Search Forward and Reverse Special PlaybackStill Image Field AdvanceDAY/TIME Search Setting the Security LockDay/Time Search Search 01 0000 will be displayed on screenSetting procedure on the first VCR is now completed Setting the BuzzerClock Adjustment Cassette Eject Setup Setting the Cassette Eject ModeEject terminal connection Eject in terminalAddress setting is flashing Settings for RS485 Terminals USE@@@@POWER@FAILURE SW OUT Terminal Output Setting Tape END OUT Terminal Output SettingOutput Terminals Tape END OUT TerminalAlarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal setting Series OUT/NON REC OUT terminal settingInput Output setting is flashing Output TerminalsCOM Terminal Remote control settingRemote Jack Output Terminals Maintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001
Top Page Image Contents