Sanyo SRT-2400DC instruction manual Remote Jack, COM Terminal, Remote control setting

Page 43

NU4QG/NA3 (SRT-2400DC GB) Mon. Sept., 17/2001

OUTPUT TERMINALS

REMOTE Jack

You can use a VA-RMN01 Remote Control Unit (sold separately) to control remotely the VCR.

NOTE:

•The functions not available on the VCR will not operate.

Remote control of the VCR is possible by connecting a remote controller with a circuit such as indicated below, to the REMOTE jack.

NOTES:

•Use a 3.5 mm mini-jack type plug.

•The connection should be done using a shielded cable no more than 5 meters long.

•The functions not available on the VCR will not operate.

Remote control setting

The remote control switch 7 can be set to either eject the tape or access the menus.

1Press the MENU button until the (SET UP 5) menu is displayed.

@@@@@@@<SET@UP@5>

*INPUT@OUTPUT@ALARM

*OUTPUT@@@@@@@SERIES

*WARN.@OUT@@@@TRANSPORT

*REMOTE@@@@@@@EJECT *TAPE@@@@@@@@@T-160

2Press the ] button, until the “REMOTE” setting is flashing.

3Press the l (or j) button to select the desired switch mode.

EJECT . . . . . . Switch 7 will eject the tape.

Remote control circuit

R0 1.2K

R1 0.3K

R2 0.43K

R3 0.51K

R4 0.62K

R5 0.75K

R6 0.91K

R7 1.1K

R8 1.3K

R9 2.0K

R10 2.4K

R11 3.6K

R12 5.6K

The resistance tolerance is 2% or less.

SW0: EJECT

SW1: STOP

SW2: PAUSE/SEARCH

SW3: REW

SW4: FF

SW5: PLAY

SW6: REC

SW7: EJECT (or MENU)

SW8: Do not use

SW9: TIMER, j

SW10: REC/PLAY SPEED CHANGE, l

SW11: TRACKING V.STILL – , ]

SW12: TRACKING V.STILL +, «

MENU. . . . . . . Switch 7 will display the menu.

4Press the PAUSE/SEARCH button to save the setting.

COM Terminal

•Common GND (ground) terminal when connecting other terminals to external devices.

42

English

Image 43

Contents SRT-2400DC For the customers in Canada PrecautionsAvoiding Electrical Shock and Fire PrecautionsMoisture Condensation Problems LocationFeatures ContentsFront Panel Locations of Controls and IndicatorsOperation Indicators Locations of Controls and IndicatorsDigital Display Wvut Q O N Back PanelBack Panel With the optional RS-485 board DC power source output DC power maximum cord Lengths About the memory resetConnections ON-SCREEN Menus ON-SCREEN Menus Setting procedure is now completed Setting the Language and ClockLanguage Setting Clock settingAutomatic Daylight Saving Time Adjustment Setting the Language and ClockDate and time are displayed Changing the ON-SCREEN DisplaySelecting the On-screen Display Changing the Date/Time Display PositionVideo Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedSetting the Type of Tape Used Video Cassette TapesIf tape management data is present on the tape Tape Management FunctionOperation If no tape management data is present on the tapeTape Management Function Setting the Tape Management FunctionConflict display sample Tape Management Conflict DisplayNormal Recording Recording Speed ModeWhen Tape in the SET UP 5 menu is set to T-160 When Tape in the SET UP 5 menu is set to T-120Recording Check Normal RecordingConcerning the Number of Times Tapes can be Rerecorded on Record PauseAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During RecordingTape Counter Notes Setting the Mode at the End of the TapeAutorepeat Recording Repeat indicator will lightAutorepeat Recording Alarm Recording Setting Alarm RecordingAlarm Mode setting is flashing Alarm Recording Counter Display Alarm RecordingChecking the Alarm Recordings Time Alarm Scan Alarm SearchProgram Timer Recording Day of the week of the 8th line is flashing Program Timer RecordingTo Cancel all Program Timer Recordings Setting the HolidaysChanging a Program Timer Recording To Cancel a Program Timer RecordingThese portions will not be recorded Series recording connections Series Recording SetupRecording will start in series recording mode Series RecordingSeries Recording Continous Loop Recording SetupLoop recording connection example with 2 VCRs Vertical Lock Control Normal PlaybackNormal Playback Tracking ControlField Advance Special PlaybackPicture Search Forward and Reverse Still ImageSearch 01 0000 will be displayed on screen Setting the Security LockDAY/TIME Search Day/Time SearchClock Adjustment Setting the BuzzerSetting procedure on the first VCR is now completed Eject in terminal Setting the Cassette Eject ModeCassette Eject Setup Eject terminal connectionAddress setting is flashing Settings for RS485 Terminals USE@@@@POWER@FAILURE Tape END OUT Terminal Tape END OUT Terminal Output SettingSW OUT Terminal Output Setting Output TerminalsOutput Terminals Series OUT/NON REC OUT terminal settingAlarm IN/CLOCK in and Alarm OUT/CLOCK OUT terminal setting Input Output setting is flashingRemote Jack Remote control settingCOM Terminal Output Terminals Maintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyNU4QG/NA3 SRT-2400DC GB Mon. Sept., 17/2001