Kodak A-61092 manual Enter

Page 33

Code

F46

F48

F48

F49

F49

F50

F51

F52

F53

F56

F56

F57

Function Code Name

Print Position

Purge Print Pattern

(for Document Printers 1 and 12)

Print Purge Head

(for Super12 Document

Printer)

Purge Frequency

(for Document Printer 1 and 12)

Align Print Image

(for Super12 Document

Printer)

Patch Reader 1 On/Off

Patch Reader 2 On/Off

End Fed Patch Reading On/Off

Patch Reading Confirmation Tone On/Off

Printer Open Jet Test (for Document Printers 1 and 12)

Printer Cartridge Status

(for Super12 Document

Printer)

Endorser On/Off

Description

Allows you to specify how far from the leading edge of the document printed information will appear. Press the Up arrow to increment the starting print position by 1 inch

(25 mm), press the Down arrow to decrement the starting print position by 1 inch (25 mm). Press the Right arrow to increment the starting print position by 0.125-inch (3 mm), or press the Left arrow to decrement the starting print position by 0.125-inch (3 mm), then press Enter.

Allows you to initiate an immediate priming ink spurt.

Allows you to initiate an automatic purging of the print heads.

This function can be done when the transport is off.

Allows you to specify how often, in terms of the number of documents fed into the transport, a priming ink spurt is initiated. Enter the number of documents, up to 50,000 and press Enter.

Allows you to specify how far to move the left half of an image up or down (in increments of one line) on the document so it will align with the right half of the image.

Allows you to turn the primary Patch Reader on or off. Enter 1 to turn on or 0 to turn off, then press Enter.

Allows you to turn the secondary Patch Reader on or off. Enter 1 to turn on or 0 to turn off, then press Enter.

Turn End Fed Patch Reading on if you expect the patch to be located in the vertical (vs. horizontal) position on the document. Enter 1 to turn on or 0 to turn off, then press

Enter.

Allows you to turn the confirmation tone on or off which informs you when the Patch Reader has successfully read a patch document. Enter 1 to turn on or 0 to turn off, then press Enter.

Allows you to determine whether or not there are nonfunctional ink jets in the Super12 Document Printer ink cartridge. Press C to return to a normal operating display.

Allows you to determine whether or not there are nonfunctional ink jets in the Super12 Document Printer. Also checks the print head(s) connection to the flex cable to assure the print heads(s) are installed properly. Press C to return to a normal operating display.

Allows you to turn the Endorser on or off. Enter 1 to turn on or 0 to turn off, then press Enter.

4-8

A-61092 September 1999

Page 32 Page 34
Image 33
Page 32 Page 34
Contents User’s Guide Page Page Introduction Scanner featuresScanner options September Rear view September Operating keys and indicators Key/IndicatorFunction Keys/Indicators Next Getting Started Turning on the scannerSelecting the language display Calibrating the scanner Unsuccessful calibration Preparing documents for scanningGap semi-automatic feeder only Adjusting the feed and separator rollerTurn the gap adjustment knob counterclockwise 2 1/2 turns Automatic feeder only Adjusting the feed shelf position semiAdjusting the feed shelf side guides Semi-automatic feeder onlyFeed Shelf Label Adjusting the exit hopper side guides and end stop Changing the deflector Overview Operating the ScannerSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Feeding thick documents Feeding documents using the automatic feeder Function Codes Using function codesFunction code summary Operation FootswitchScanning EndorserPatch Reader Super12 Document PrinterCode Function Code NameDescription F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 Code Function Code Name Enter F58 F59 F60 F62 F63 F64 F65 F66 F70 F71 F72 F73 F74 F75 F91 F92 F93 F94 F95 F96 F97 F98 F99 Cleaning tasks Cleaning materials Replacement parts MaintenanceCleaning the imaging guides Daily maintenance proceduresSeptember Roller cover Release lever Feed roller Separator roller Cleaning the feeder module and separator roller Cleaning the separator roller Cleaning the paper path Vacuuming inside the scanner September September Weekly maintenance procedures Cleaning the exposure lamp housingsCleaning the cabinet Cleaning the air filter Monthly maintenance proceduresReplacing the air filter Replacement proceduresReplacing the exposure lamps September Replacing the imaging guides Replacing the feeder module Replacing the feeder module and separator rollerReplacing the separator roller Ordering replacement parts Ordering cleaning materials Operator Messages Operator message listing Code Operator Message DisplayedDescription/Action Required Code Code Code E281 E282 E285 E286 E291 E293 E294 E295 E296 E297 E298 Code Various messages Trouble and remedy chart TroubleshootingTrouble Probable CauseTrouble Document path Clearing the document pathClearing documents Feeder/horizontal transport area Imaging guide area Lower roller assembly area Vertical transport area Upper turn area Document exit area Accessories Supplies Supply Catalog #Imaging Station Lamps Supply Catalog # Part/Tool Parts and toolsUnited States and Canada Order Number All other regionsUsing the Bar Code Reader Code Type Bar code typesCharacter Set Available Characters in Set Start/Stop CharactersBar code placement Before you begin Enabling the bar code confirma- tion tone Enabling bar code readingPerforming a bar code test September Static bar code evaluation Using the Evaluate optionSelect 1=EVALUATE Select either 1=Transport Off or 2=Transport OnUsing the Imaging Station Cutting line 12.5 mm Dynamic bar code evaluation Evaluating test results Dimensional Fields Pass or FailGrade Field Pass 31 to Fail Reflectance Fields Grades a through FProblem Type Common Causes of Low Bar Code Ratings FieldCause Using the %KODAK option Using the Display optionUsing the %NORM option September Using the check feeder Using the Check Feeder / Check StackerClearing jams in the check feeder Cleaning the check feeder Using the check stacker Die styles Using the EndorserBefore you begin Changing the die drum Endorser Locking lever Latch Endorser rotates to the right Die Spring clip Pry off at this edge Changing the ink roller Setting the date and code number Enabling Endorser Changing the print position Selecting the Endorser modeUsing the Footswitch Footswitch Pressed Action Enabling the confirmation tone Footswitch Pressed actionsFootswitch Released actions Footswitch Pressed DefinitionFootswitch Released Action Patch types Using the Patch ReaderPatch code placement Positioning the Patch Reader Sensor Appendix a Basic Concepts ModesLinked modes Image addresses Using the Next key Assigning an image address∙ Enter Using Function Code F92 Image address formats Indexing schemesSingle level indexing Two level indexing Image Address Three level indexing Three level offset indexing Level instruction Controlling document level changesDocument A G I N G
Top Page Image Contents