Kodak A-61092 manual Code

Page 57

Code

E204

E205

E206

E207

E211

E214

E219

E220

E221

E225

E226

E227

E228

E229

Operator Message Displayed

Skewed document — refeed

Level overflow — press next level

Check print head

Check printer installation

Enter correct Image Address

Document length error — refeed

Clear error and refeed last doc

Check for jam in entrance transport

Clean entrance sensor

Check for jam in transport

Clean slide-out sensor reflector

Check for jam in transport

Check for jam in upper transport

Clean exit sensor

Description/Action Required

Press Clear and use the Next key to enter the correct image address and refeed document(s).

Press Clear and use the Next key to enter the correct image address, or press a level key for a higher level.

Install the correct Document Printer print head.

Document Printer not correctly installed.

Properly install the Document Printer print head.

Use the Next key to enter the correct image address.

Press Clear and use the Next key to enter the correct image address and refeed document(s).

Press the Clear key. Press Run and feed the last document.

Clear the document path.

Press Clear and then press the Jog key.

Press Run and refeed document(s).

Perform maintenance/cleaning procedures.

Clear the document path.

Press Clear and then press the Jog key.

Press Run and refeed document(s).

Perform maintenance/cleaning procedures.

Clear the document path.

Press Clear and then press the Jog key.

Press Run and refeed document(s).

Clear the document path.

Press Clear and then press the Jog key.

Press Run and refeed document(s).

Perform maintenance/cleaning procedures.

6-4	A-61092 September 1999

Image 57

Contents User’s Guide Page Page Introduction Scanner featuresScanner options September Rear view September Operating keys and indicators Key/IndicatorFunction Keys/Indicators Next Getting Started Turning on the scannerSelecting the language display Calibrating the scanner Unsuccessful calibration Preparing documents for scanningGap semi-automatic feeder only Adjusting the feed and separator rollerTurn the gap adjustment knob counterclockwise 2 1/2 turns Automatic feeder only Adjusting the feed shelf position semiAdjusting the feed shelf side guides Semi-automatic feeder onlyFeed Shelf Label Adjusting the exit hopper side guides and end stop Changing the deflector Overview Operating the ScannerSelecting a mode Temporary operating values Feeding documents using the semi- automatic feeder Feeding thick documents Feeding documents using the automatic feeder Function Codes Using function codesFunction code summary Operation FootswitchScanning EndorserPatch Reader Super12 Document PrinterCode Function Code NameDescription F17 F18 F19 F20 F21 F22 F23 F34 F37 F38 F39 Code Function Code Name Enter F58 F59 F60 F62 F63 F64 F65 F66 F70 F71 F72 F73 F74 F75 F91 F92 F93 F94 F95 F96 F97 F98 F99 Cleaning tasks Cleaning materials Replacement parts MaintenanceCleaning the imaging guides Daily maintenance proceduresSeptember Roller cover Release lever Feed roller Separator roller Cleaning the feeder module and separator roller Cleaning the separator roller Cleaning the paper path Vacuuming inside the scanner September September Weekly maintenance procedures Cleaning the exposure lamp housingsCleaning the cabinet Cleaning the air filter Monthly maintenance proceduresReplacing the air filter Replacement proceduresReplacing the exposure lamps September Replacing the imaging guides Replacing the feeder module Replacing the feeder module and separator rollerReplacing the separator roller Ordering replacement parts Ordering cleaning materials Operator Messages Operator message listing Code Operator Message DisplayedDescription/Action Required Code Code Code E281 E282 E285 E286 E291 E293 E294 E295 E296 E297 E298 Code Various messages Trouble and remedy chart TroubleshootingTrouble Probable CauseTrouble Document path Clearing the document pathClearing documents Feeder/horizontal transport area Imaging guide area Lower roller assembly area Vertical transport area Upper turn area Document exit area Accessories Supplies Supply Catalog #Imaging Station Lamps Supply Catalog # Part/Tool Parts and toolsUnited States and Canada Order Number All other regionsUsing the Bar Code Reader Code Type Bar code typesCharacter Set Available Characters in Set Start/Stop CharactersBar code placement Before you begin Enabling the bar code confirma- tion tone Enabling bar code readingPerforming a bar code test September Static bar code evaluation Using the Evaluate optionSelect 1=EVALUATE Select either 1=Transport Off or 2=Transport OnUsing the Imaging Station Cutting line 12.5 mm Dynamic bar code evaluation Evaluating test results Dimensional Fields Pass or FailGrade Field Pass 31 to Fail Reflectance Fields Grades a through FProblem Type Common Causes of Low Bar Code Ratings FieldCause Using the %KODAK option Using the Display optionUsing the %NORM option September Using the check feeder Using the Check Feeder / Check StackerClearing jams in the check feeder Cleaning the check feeder Using the check stacker Die styles Using the EndorserBefore you begin Changing the die drum Endorser Locking lever Latch Endorser rotates to the right Die Spring clip Pry off at this edge Changing the ink roller Setting the date and code number Enabling Endorser Changing the print position Selecting the Endorser modeUsing the Footswitch Footswitch Pressed Action Enabling the confirmation tone Footswitch Pressed actionsFootswitch Released actions Footswitch Pressed DefinitionFootswitch Released Action Patch types Using the Patch ReaderPatch code placement Positioning the Patch Reader Sensor Appendix a Basic Concepts ModesLinked modes Image addresses Using the Next key Assigning an image address∙ Enter Using Function Code F92 Image address formats Indexing schemesSingle level indexing Two level indexing Image Address Three level indexing Three level offset indexing Level instruction Controlling document level changesDocument A G I N G